Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: JohnStamos

    Page 1 of 13 1 2 3 4

    Search: Search took 0.21 seconds.

    1. Replies
      28,921
      Views
      2,522,845

      When the prop valve is seized, remove the nut,...

      When the prop valve is seized, remove the nut, back the bolt out til it hits the prop valve, wiz wheel it off, back it out again, whiz wheel it off, repeat. It takes 4-5 cuts to get it out, but...
    2. Replies
      8
      Views
      386

      I've cut them on the brake lathe then balanced on...

      I've cut them on the brake lathe then balanced on a tire balancer. Drilling opposing side to balance.

      Takes forever on a brake lathe, but free is free.
    3. In the Mk4 12v the cat is integral with the...

      In the Mk4 12v the cat is integral with the downpipe. You either chop the cat off, fab a collector/megaphone, then build a test pie, or swap to a Mk3 downpipe, and fab a test pipe. The Mk3 downpipe...
    4. Metal to metal and grease the flanges with Moly...

      Metal to metal and grease the flanges with Moly Grease. Temp cycle the car and it cokes the grease into a carbon gasket.
    5. Replies
      3,863
      Views
      731,943

      You can get JIC/AN -> tubing fittings that are...

      You can get JIC/AN -> tubing fittings that are rated for 5000 PSI working 7500PSI Burst.
    6. Replies
      3,863
      Views
      731,943

      On Dual 81's. Not a single. Looks like...

      On Dual 81's. Not a single.



      Looks like a BW S500SX. Keeping an eye on this one. :thumbup::thumbup::thumbup:
    7. Throttle body to MAF tube is Spectre 94963 + 3"...

      Throttle body to MAF tube is Spectre 94963 + 3" hump hose. Cut to fit. ~$50

      I know people are always looking for this.


      Then its a 75 degree bend into the fender if you keep the intake piping...
    8. Replies
      617
      Views
      144,704

      Passat harness has more sub harnesses than the...

      Passat harness has more sub harnesses than the Mk3 style. Think of it as a mix of CE2 Mk2 and Mk3.
    9. Replies
      6
      Views
      1,021

      I know its way late, but just made one and...

      I know its way late, but just made one and figured I'd post.


      mpxh6300ac6u freescale sensor. Its .2-5v sensor swing. 44PSI absolute, so 3 bar over atmospheric.

      They are made to be board...
    10. Replies
      8
      Views
      1,071

      Shoot me a PM with your bottom line price. I...

      Shoot me a PM with your bottom line price. I have a trailer and cash waiting, and I'm only 15mins from Avonmore.

      Don't worry about the fender, I have some and will be a donor car most likely...
    11. Replies
      28,921
      Views
      2,522,845

      Looking amazing Pk. :thumbup::thumbup:

      Looking amazing Pk. :thumbup::thumbup:
    12. Floor pans.

      Floor pans.
    13. Replies
      6
      Views
      1,021

      I know I'm a little late, but the repop Chinese...

      I know I'm a little late, but the repop Chinese 3bar sensors don't have the same curve as the OEM GM sensor, or the Omnipowers/ect. Been down that road before troubleshooting someone elses junk. ...
    14. Replies
      3,863
      Views
      731,943

      So it drains into a shampoo bottle to be...

      So it drains into a shampoo bottle to be re-purposed for a Saturday club outing?







      :laugh:
    15. Ask BFI, MJMautohaus, ect how they do it. Hell,...

      Ask BFI, MJMautohaus, ect how they do it. Hell, look at Gonzo.

      The VW community isn't the brightest when it comes to venders.
    16. Almost every Obd2 12v C2 tune I have seen is like...

      Almost every Obd2 12v C2 tune I have seen is like this.

      I have one that runs GREAT WOT and at temp, but cold, misfires to the point you have to rev out the motor 3-4 times before you can drive...
    17. If you only want to spring for one, buy a 1/2"...

      If you only want to spring for one, buy a 1/2" flame tip double cut burr. It will do everything, just not ideal in all situations and you can't make large flat cuts. A good one will set you back $30
    18. Just run a c2 chip with a non baffled exhaust. ...

      Just run a c2 chip with a non baffled exhaust. They overfuel so badly on decel that it's hard to keep it from popping. Great if you are 16 I guess.
    19. Replies
      16
      Views
      1,478

      Can't decide if its the shoddy body work on the...

      Can't decide if its the shoddy body work on the car that makes them look like they fit like garbage, or the flares themselves.

      If fitment is cleaned up, I am in for a set.
    20. Replies
      31
      Views
      4,497

      Running a 50/60 weight in a car with stock...

      Running a 50/60 weight in a car with stock clearances is going to cause more harm then good. 10w/60 in this application is moronic. You will be popping the pressure relief valve at VERY low rpm,...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4