Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: ziggirocco

    Page 1 of 13 1 2 3 4

    Search: Search took 0.22 seconds.

    1. Yup Bracing for impact

      Yup
      Bracing for impact
    2. Replies
      0
      Views
      26

      WTB gas tank heat shield for '81

      The thin heat shield between the gas tank and exhaust pipe is what I'm looking for. PM me if you have a good clean one.

      Thanks!
    3. Looking for gas tank heat shield for '81

      I've looked online at the usual places, eBay, gap, mk1 autohaus. Etc

      Can't seem to find anywhere. Anyone know where it can be found if at all? Will see if by any chance it is still available from...
    4. Replies
      4,545
      Views
      384,661

      Took off the rear beam and tank ...

      Took off the rear beam and tank

      http://images.tapatalk-cdn.com/16/02/06/55922a851d063f72a83a5bdda41f99e6.jpg
    5. Replies
      199
      Views
      20,270

      I did a bad thing today...

      Ok, so i had some time to get some work done today.

      http://images.tapatalk-cdn.com/16/02/06/e9355c64bb54ceaa3495890ed30f388b.jpg
      ...
    6. Replies
      249
      Views
      38,561

      Sticky: The Unofficial Buyer/Seller Feedback Thread

      Vw90

      X3 [emoji106]
    7. Replies
      4
      Views
      165

      What Hal said...

      What Hal said...
    8. Replies
      12
      Views
      319

      Well.... Too short, too much glare, too many nice...

      Well.... Too short, too much glare, too many nice Vws, not enough red cars. Now get back to filming!!

      I want to be entertained!

      [emoji106]
    9. Replies
      9
      Views
      311

      Seems like another weak point exposed! Now go...

      Seems like another weak point exposed! Now go back and fix it! Looked like regular connecting rods etc., I would have imagined at that point most or all the bottom end would be forged.
    10. Replies
      28
      Views
      672

      That same area under the hood in the rain tray,...

      That same area under the hood in the rain tray, if not we'll seam sealed or if the seam sealer has cracked etc might cause that. I would recommend you pull out the cover and take a good look.
      ...
    11. Replies
      199
      Views
      20,270

      Thanks for the input Hal will be looking at the...

      Thanks for the input Hal will be looking at the padding.

      The brackets I got used out of Arizona..... Yes the OCD continues, they will be blasted and powder coated as will as many parts as possible...
    12. Replies
      199
      Views
      20,270

      Got my hands on some near mint fuel pump and...

      Got my hands on some near mint fuel pump and accumulator brackets. Out of 4 I should get at least 2-3 near perfect ones.
      ...
    13. Replies
      5
      Views
      233

      I would doubt moving the wheels will do anything....

      I would doubt moving the wheels will do anything. The base of the cable had a steel cup or sleeve type end that is pushed int the Trans and held down by a small plate and a bolt. I assume the bolt...
    14. Replies
      22
      Views
      576

      Lol I tend to try and over engineer things a...

      Lol
      I tend to try and over engineer things a bit, but in this case I'm trying to keep it simple and hold myself back it I need to keep it strong enough to be able to leave it on the rig for a few...
    15. Replies
      22
      Views
      576

      Car dolly / rig looking for ideas

      Wish I could take credit for the welds, but I left it to my buddy seeing the stakes are high lol
      He did do very nice welds.
      Thanks

      I was thinking goes my something like this but less intricate...
    16. Replies
      22
      Views
      576

      Valid points guys. I'm going back to the...

      Valid points guys.

      I'm going back to the drawing board lol
      I took a close look at the mounting point sheet metal and I thought it was straight initially it actually is on an angle and will be...
    17. Replies
      22
      Views
      576

      Ya I plan to brace them together and also maybe...

      Ya I plan to brace them together and also maybe brace another arm someplace to the undercarriage just to keep it all locked in, wood is strong I'll see when I drop the beam.
    18. Replies
      22
      Views
      576

      Well started on the project Got 2 super duper...

      Well started on the project
      Got 2 super duper casters and we dabbed up a set of stands.
      I made them a bit higher than ride height do have a bit of room when it's going to be on the ground. And to...
    19. Replies
      31
      Views
      908

      Not cool dude, I Don't really care who likes...

      Not cool dude,

      I Don't really care who likes me on here or not etc., but Fred Is a good guy and is one of the few guys on here ACTUALLY DOING SOMETHING do help the scirocco community. So before...
    20. Replies
      22
      Views
      576

      Car dolly / rig looking for ideas

      Thanks for the input guys!
      Working on a set up as we speak.
      Thanks Fred
      I have 4 of those dollies too , just found them lol.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4