Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: iZOTOPE

    Page 1 of 5 1 2 3 4

    Search: Search took 0.84 seconds.

    1. Replies
      1,735
      Views
      626,103

      Re: 16V G60 - How to

      i am using ngk bkr7esc, as for the cams 268 are for NA applications, but i think they will work :)

      Sent from my Nexus 4 using Tapatalk
    2. Replies
      1,735
      Views
      626,103

      as a belt tensioner i used 3 timing belt...

      as a belt tensioner i used 3 timing belt tensioners from 8v. in the picture below you can see 2 of them, and one is in place of that plastic roller from the G60 bracket, i replaced those because i...
    3. Replies
      7
      Views
      1,007

      i too have these hesitations when I go up in...

      i too have these hesitations when I go up in rpms, or if i press the throttle to the floor and boost kicks in, afr shows lean, lots of missfires like fuel cut is kicking in, but i'm on megasquirt, no...
    4. Replies
      1,735
      Views
      626,103

      well, don't have an mk1, but for my mk2 i...

      well, don't have an mk1, but for my mk2 i fabricated a bracket for the alternator from 3mm stainless steel sheet, it looks ok, and all pulleys are perfectly centered.

      you could make a bracket like...
    5. Replies
      1,735
      Views
      626,103

      if you have a ms2 i can help you with the config...

      if you have a ms2 i can help you with the config and wiring diagram, it should get you started but you'll need to dyno tune it afterwards.
    6. Replies
      1,735
      Views
      626,103

      ah, and i forgot, always use a crank pulley with...

      ah, and i forgot, always use a crank pulley with harmonics damper!
    7. Replies
      1,735
      Views
      626,103

      reply

      144mm rods, s2 pistons, metal head gasket, and the compression ratio should be ok, make sure the pistons do not touch the oil squirters from the PG block ...

      the g60 piston dish is way more...
    8. Replies
      3
      Views
      680

      well my ignition setting are ok, and the car ran...

      well my ignition setting are ok, and the car ran ok, pulls very strong, spark plugs look ok, timing is ok, measured with the .
      the LC-1 sensitivity was set to highest and 60% lambda averaging...
    9. Replies
      3
      Views
      680

      Innovate LC-1 troubles

      I was driving with my car to tune my VE tables, brand new LC-1 is wired as per manual, good grounds, gauge reads ok, all of a sudden it reads 22AFR and then goes 8.3AFR or so, and stays there, I've...
    10. Replies
      4
      Views
      1,696

      i'm not looking for mad power, 210-220 crank hp...

      i'm not looking for mad power, 210-220 crank hp is enough for me, my car is light about 850kilos, so with that power it should be a blast to drive.
      i was asking the first questions because my G60s...
    11. Replies
      4
      Views
      1,696

      1.8 16v and eaton m45 combo

      Let us talk about the eaton m45 on 1.8 16v engines.
      I've done some searching and researching on this matter, and I didn't find much info other than "just put an m62 and you're good...or the m45 is...
    12. Replies
      476
      Views
      189,277

      reply

      look at this one, i think this is for a rod linkage

      http://gallery.visualrealms.com/data/media/167/motorsportshifter_002.jpg...
    13. Replies
      476
      Views
      189,277

      reply

      how about we all think about a method to do such a shifter for the rod assembly?
      what i'm trying to say, is keep the orriginal rods from the tranny to the cockpit, and do an assembly that bolts on,...
    14. Replies
      1,735
      Views
      626,103

      reply

      mine 1.8 16vG60 :D
      http://imageshack.us/a/img145/272/photo0862.jpg
    15. Replies
      3,303
      Views
      2,211,153

      finally

      Been watching this thread from day 1, I'm glad to see this car rolling on the track!
      Best wishes and success on your racing career :) :beer::beer::beer:
    16. Replies
      27,177
      Views
      2,372,692

      16vG60

      completed the bottom end of my 1.8 8v to 1.8 16vG60 conversion.
      some photos:
      http://img403.imageshack.us/img403/5990/photo0514.jpg
      http://img62.imageshack.us/img62/700/photo0515m.jpg...
    17. Replies
      126
      Views
      28,289

      reply

      my models aren't so much detailed, the grill is a simple mesh and a high resolution texture that fills it.

      well, my project is about customizing the cars, the users can change lots of things from...
    18. Replies
      126
      Views
      28,289

      reply

      hey Gavh, i can help you with my interior models, you'll need to resize it to fit your needs.

      cheers,

      iZOTOPE
    19. Replies
      126
      Views
      28,289

      nice model. i've started a programming project...

      nice model.

      i've started a programming project couple of years ago, it is called VeedubCustomizer, i have some low poly models for mk1, mk2, mk3, mk4 and mk5, the mk1 is fully customizable, wheel...
    20. in trigger return mode it lights up if spark...

      in trigger return mode it lights up if spark occures and on more ignition settings i can set the middle led to off or ignition trigger indicator, in toothed wheel mode the middle led indicator option...
    Results 1 to 20 of 89
    Page 1 of 5 1 2 3 4