Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: vdubxcrew

    Page 1 of 13 1 2 3 4

    Search: Search took 0.37 seconds.

    1. Shell Rotella synthetic oil Ok for my TSI?

      I run 5-40 shell rotella in my 98 passat 1.8t and was thinking about using it on my wifes new 15 TSI but I know the newer motors are a little more oil specific. Will the Rotella be fine?
    2. Still have these?

      Still have these?
    3. Replies
      9
      Views
      588

      Obd2 chip?

      Obd2 chip?
    4. Replies
      3
      Views
      177

      Pm sent

      Pm sent
    5. Replies
      3
      Views
      177

      WTB: full obd2 vr6 engine harness

      From fuse block to ecu and injectors. In very good shape please.
    6. Best OBD2 harness for my 95 VR...passat or golf/jetta?

      Looking to do a obd2 swap on my 95 gti vr6. Which is a more straight forward harness to swap in? One from a 96-97 passat or one from a 96-99 gti/jetta? My car doesn't have ac and the cooling fans are...
    7. Replies
      1
      Views
      124

      Wtb: OBD1 VR6 throttle body

      Looking for a good shape obd1 vr6 throttle body with good working tps sensor.
    8. Replies
      5
      Views
      476

      Sold

      Sold
    9. Replies
      5
      Views
      476

      Replied

      Replied
    10. Replies
      7
      Views
      776

      Is it ported and polished?

      Is it ported and polished?
    11. Replies
      1
      Views
      150

      WTB: B3 headlight harness WITH FOGS

      Looking for a clean unmolested headlight/fog harness.
    12. Replies
      4
      Views
      264

      These the blue ones? Can you post a better pic to...

      These the blue ones? Can you post a better pic to show condish?
    13. Replies
      5
      Views
      476

      Up

      Up
    14. Thread: 2.0 to vr6

      by vdubxcrew
      Replies
      7
      Views
      701

      Thinking about doing this as well. I have a mint...

      Thinking about doing this as well. I have a mint body B3 but have had non-stop problems with the 16v in it. I am pretty familiar with 12v vr6's. Is it a must to swap in the k-frame and front motor...
    15. Vr6 swap into a 16v B3 Passat...need different subframe?

      I've heard its not necessary. I just need to swap the 16v rear motor mount bracket onto the vr6, and use a vr6 front motor mount bracket. Anyone confirm?
    16. UPdate. I had the stainless rings removed and had...

      UPdate. I had the stainless rings removed and had soft copper rings put in. The heads not on yet. I'll report later. May have to file down the rings a little to make sure they will seal properly with...
    17. I don't have a standard F or G trim V5. Those are...

      I don't have a standard F or G trim V5. Those are only good for around 14-15psi and they can't spin to the spec mine has. The H-trim is a prototype that has Abec 9 bearings, custom impeller wheel,...
    18. Replies
      3
      Views
      197

      Pretty sure they don't sell an a/c pulley.

      Pretty sure they don't sell an a/c pulley.
    19. Vortech V5 H-trim, cogged, 15-20psi.

      Vortech V5 H-trim, cogged, 15-20psi.
    20. Replies
      1
      Views
      331

      VR6 ecu's commonly sell in our classifieds for...

      VR6 ecu's commonly sell in our classifieds for right around $50 with or without shipping on average.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4