Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: zrau17

    Page 1 of 13 1 2 3 4

    Search: Search took 0.71 seconds.

    1. Replies
      3
      Views
      231

      The spindle could be bent, if you replaced the...

      The spindle could be bent, if you replaced the suspension and know the strut isn't bent that'd be my next guess.
    2. Because the marks are actually really close for...

      Because the marks are actually really close for TDC and you may not notice it being one tooth off. There's actually a specific number of teeth from the cam gear mark to the notch on the crank gear....
    3. Replies
      88
      Views
      5,962

      Wow. Not on here very much anymore…but this is...

      Wow. Not on here very much anymore…but this is just wow. This is the build I've always wanted to do, props for doing it beyond correctly :thumbup:
    4. Check the bleeder block where the clutch line...

      Check the bleeder block where the clutch line goes into the top of the trans first, same thing happened to me and I thought slave and the o-ring in the bleeder block blew out. Much much cheaper...
    5. :thumbup:

      :thumbup:
    6. Replies
      7
      Views
      303

      What kind of diverter valve, on my old 3071r...

      What kind of diverter valve, on my old 3071r setup at 21psi or above the DV didn't really like holding the pressure very much and would flutter. The highest spring rate in a 007 I know is like...
    7. Buy these please. Make an offer.

      Buy these please. Make an offer.
    8. Feeler FS: smaller frame "big turbo setup" for 1.8t

      SOLD
    9. Thread: Sketchy?

      by zrau17
      Replies
      6
      Views
      341

      You can't be worried about strength here…10.9 is...

      You can't be worried about strength here…10.9 is 10.9. To list them as that grade they'd have to be tested I'm sure. There's JDM cars that all use m12 and make MUCH more power generally to the rear...
    10. Only other guess would be the rear axle beam...

      Only other guess would be the rear axle beam bushings. Check all your bolts suspension wise and make sure things are tight. With that many miles and assuming the bushings have never been changed, I'd...
    11. Replies
      11
      Views
      311

      Make sure it's the slave cylinder first…I had...

      Make sure it's the slave cylinder first…I had this same thing happen and I just got frustrated and ordered a new slave and when I went to take it apart I pulled the bleeder block and clutch line and...
    12. FS: Full bolt on big turbo kit 1.8t, BT in a box. 08085

      http://forums.vwvortex.com/showthread.php?7018823-FS-Full-bolt-on-big-turbo-kit-1-8t-BT-in-a-box
    13. FS: Full bolt on big turbo kit 1.8t, BT in a box.

      EDIT: As of right now I'm not finding what I need to get the car going where I want it to. My cheapest and fastest option may be to rebuild it for now and see what happens. Sorry to anyone...
    14. FS: Full bolt on big turbo kit 1.8t, BT in a box.

      EDIT: As of right now I'm not finding what I need to get the car going where I want it to. My cheapest and fastest option may be to rebuild it for now and see what happens. Sorry to anyone...
    15. The three bolts in the center of the valve cover,...

      The three bolts in the center of the valve cover, between the coil packs…are m6x50. The rest are m6x40. I haven't had any problems using them yet. Just be careful when putting the gasket on because...
    16. :thumbup:

      :thumbup:
    17. All of the bolts on what, the compressor housing?...

      All of the bolts on what, the compressor housing? It's not going to be easy, all I can tell you is try removing the oil lines if you haven't already and just see what you can do. May have to just...
    18. Replies
      39
      Views
      2,281

      Was gonna say that, I think he might mean track...

      Was gonna say that, I think he might mean track width maybe…I dunno.

      I run 9.5/10.5et14 and that's a little wide but I wouldn't call it stupid lol
    19. Replies
      11
      Views
      376

      Came in to say this, good info here :thumbup: Not...

      Came in to say this, good info here :thumbup: Not many people realize that. The pickup tube doesn't like foamy oil, you're losing suction and in turn oil pressure.
    20. Replies
      39
      Views
      2,281

      Could've had them redrilled and not fiberglassed...

      Could've had them redrilled and not fiberglassed the hell out of the car.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4