Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Pat @ Pitt Soundworks

    Page 1 of 13 1 2 3 4

    Search: Search took 0.24 seconds.

    1. http://imgur.com/LtPotM7.gif...

      http://imgur.com/LtPotM7.gif
      http://imgur.com/qc7zS7N.gif
      http://imgur.com/EekGOMW.gif
      http://imgur.com/WHAOpBt.gif
      http://imgur.com/kUWchmL.gif
    2. FS: hx52 and twin scroll manifold for 1.8t

      I'm selling a manifold I built for a 1.8t project I just don't have the time to work on any more.

      The manifold is twin scroll, stainless steel, with mild steel flanges. 1.5" runners,(almost equal...
    3. Replies
      549
      Views
      132,754

      Ugh that sucks. It would be so much easier if...

      Ugh that sucks. It would be so much easier if they tried to be helpful.
    4. Replies
      549
      Views
      132,754

      That's what I mean, instead of drilling out after...

      That's what I mean, instead of drilling out after the fact. Contact the manufacturer and have it drilled correctly at manufacturing. I've contacted a few and its not a big deal.
    5. Replies
      549
      Views
      132,754

      Why wouldn't you just order a 02m clutch kit with...

      Why wouldn't you just order a 02m clutch kit with the flywheel drilled for the 8 bolt pattern? Seems easier than trying to cram a tfsi clutch kit in to the 02m
    6. It's just a matter of time, but everything from...

      It's just a matter of time, but everything from cycle load, psi, motor mount conditions, road conditions, tire and suspension, IC mounted rigidity, and pipe weight and routing all play a factor. The...
    7. Groggy, If you can stand a week or two of down...

      Groggy,

      If you can stand a week or two of down time I can get you fixed up and build a support. Aluminum is super finicky when repairing cracks. Once it's welded, it loses its temper, and once...
    8. Replies
      549
      Views
      132,754

      01e is not transverse. No special parts required.

      01e is not transverse. No special parts required.
    9. Replies
      204
      Views
      42,528

      Thanks I thought about it but frankly, I don't...

      Thanks

      I thought about it but frankly, I don't see the point. The rotors can not flow any air unless spinning and the bypass oraface is roughly 25mm. If the throttle was after the blower and I...
    10. Not only do they have to be in the same posision,...

      Not only do they have to be in the same posision, they have to be in the same orientation and direction.
    11. Replies
      549
      Views
      132,754

      http://i.imgur.com/hSOprak.jpg...

      http://i.imgur.com/hSOprak.jpg
      http://i.imgur.com/oxuk3EH.jpg
      http://i.imgur.com/WiYpwEV.jpg
      http://i.imgur.com/Cm3b2FI.jpg
      http://i.imgur.com/s1aAUjH.jpg
      http://i.imgur.com/4lozAn0.jpg...
    12. Replies
      204
      Views
      42,528

      So, I finally have had some time and desire to...

      So, I finally have had some time and desire to start working on this turd again. The car is in a state of neglect and turmoil and it's every bit as bad as it looks in the pictures. A little TLC and...
    13. Replies
      1,092
      Views
      275,041

      Spool can be affected by a lot of other things...

      Spool can be affected by a lot of other things like intercooler pipe length and diameter and exhaust manifold and downpipe size. Optimizing any of these will pick up spool. Another option would be...
    14. Replies
      1,092
      Views
      275,041

      No. The 50 trim will out spool the hy35. Even...

      No. The 50 trim will out spool the hy35. Even the biggest stage three 50 trim turbine wheel is smaller than the smallest hy35 wheel. And the 50 trim can be had with much smaller Turbine wheels.
    15. Replies
      1,092
      Views
      275,041

      Dunno how many people are still interested, but I...

      Dunno how many people are still interested, but I just got an interesting unit in. Part number 4036617. It's a 7 blade 56mm hx35, but it uses the hy35 compressor cover, so the compressor cover...
    16. use the 4 piece washer. more thrust surface is...

      use the 4 piece washer. more thrust surface is always better than less
    17. Replies
      549
      Views
      132,754

      Starting the image dump. The main section of the...

      Starting the image dump. The main section of the pan is done. Timing chain rail is next. Hopefully the TTRS pulley comes in thursday so the pump drive mandrel will be finished by the weekend.
      ...
    18. Replies
      549
      Views
      132,754

      Any guesses? http://i.imgur.com/5lSIHkx.jpg...

      Any guesses?

      http://i.imgur.com/5lSIHkx.jpg
      http://i.imgur.com/pDH4E9U.jpg
    19. Replies
      549
      Views
      132,754

      Thanks dude. Is that s4 of your ready to hit the...

      Thanks dude. Is that s4 of your ready to hit the streets?

      I've been waiting on commissioned work for the past three months. Just got word that hopefully I'll have some awesome pictures to show...
    20. Replies
      549
      Views
      132,754

      Sneak peak. 4140 billet ...

      Sneak peak. 4140 billet

      http://i.imgur.com/ZjWdDhI.jpg
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4