Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: thewhitsnpt

    Page 1 of 13 1 2 3 4

    Search: Search took 0.84 seconds.

    1. Replies
      10,001
      Views
      307,031

      #2015nedustoffcluboftheyear?

      #2015nedustoffcluboftheyear?
    2. Replies
      1,626
      Views
      429,931

      On aluminum yes they will. Stainless not so much....

      On aluminum yes they will. Stainless not so much. Just beware of the inside diameter of the tubing as it needs to fit over the steel sleeve in the fittings. I actually had to drill out ends to make...
    3. Replies
      1,626
      Views
      429,931

      V2 has everything built into the ecu/manifold.

      V2 has everything built into the ecu/manifold.
    4. Replies
      1,626
      Views
      429,931

      Got it.

      Got it.
    5. Replies
      1,626
      Views
      429,931

      Looks great man. I am a little confused as to...

      Looks great man. I am a little confused as to what the lines go to tho lol. Compressor to tank x2 I see but what are 4 other lines? Older management?
    6. What's it fit?

      What's it fit?
    7. Replies
      63,809
      Views
      2,359,551

      That's very cool

      That's very cool
    8. Replies
      1
      Views
      144

      Holy pop ups on your site

      Holy pop ups on your site
    9. Replies
      75,161
      Views
      2,803,643

      Then get on it slacker. It's a beautiful day...

      Then get on it slacker. It's a beautiful day today.
    10. Replies
      63,809
      Views
      2,359,551

      Ha ha ha

      Ha ha ha
    11. Replies
      1,626
      Views
      429,931

      I just ordered aluminum tubing from McMaster...

      I just ordered aluminum tubing from McMaster Carr. Now I can use my ptc fittings. Anyone need some 3/8" stainless? Have 20'of it.
    12. We generally close pre reg a couple weeks before...

      We generally close pre reg a couple weeks before show.
    13. Replies
      63,809
      Views
      2,359,551

      Apparently there is an issue with tubing as it...

      Apparently there is an issue with tubing as it should work perfectly fine with ptc fittings. I had the od checked by a machine shop to verify it was within spec and it is. Jeremy at Airlift is asking...
    14. Replies
      63,809
      Views
      2,359,551

      I've get a good bender so not so bad. Looks like...

      I've get a good bender so not so bad. Looks like I'll be doing some. Research tonite. Lol
    15. Replies
      63,809
      Views
      2,359,551

      I'll figure it out. Figured maybe you already had...

      I'll figure it out. Figured maybe you already had lol. Thanks duder.
    16. Replies
      63,809
      Views
      2,359,551

      Yeah its 3/8 id ss tubing. It's just harder than...

      Yeah its 3/8 id ss tubing. It's just harder than the nylon so the fittings won't grab it.
    17. Replies
      63,809
      Views
      2,359,551

      They won't grab the ss tubing. It goes right in...

      They won't grab the ss tubing. It goes right in but pulls back out since the collet can't dig into tubing. Using straight up ss tubing btw.
    18. Replies
      63,809
      Views
      2,359,551

      I'm running Airlift btw

      I'm running Airlift btw
    19. Replies
      63,809
      Views
      2,359,551

      I don't know if they will seal or not. But they...

      I don't know if they will seal or not. But they slide right out after pushing them in. Assume they would push out under pressure.
    20. Replies
      63,809
      Views
      2,359,551

      Pulls right out. I'm assuming a brass tube to...

      Pulls right out. I'm assuming a brass tube to compression fitting from manifold and then to ss tube.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4