Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: All_Euro

    Page 1 of 13 1 2 3 4

    Search: Search took 0.84 seconds.

    1. Replies
      4
      Views
      188

      Here you go......

      Here you go... http://www.verdictmotorsports.com/ProductDetails.asp?ProductCode=VMS107
    2. Replies
      18
      Views
      634

      This would be awesome :thumbup:

      This would be awesome :thumbup:
    3. I had one fail recently - took a chunk out of the...

      I had one fail recently - took a chunk out of the timing belt too. Thankfully the belt stayed put and nothing else was damaged.
      ...
    4. Replies
      37
      Views
      759

      18-20 hg is what you'll want to see

      18-20 hg is what you'll want to see
    5. Replies
      37
      Views
      759

      I had a leak that I couldn't find for quite a...

      I had a leak that I couldn't find for quite a while and it turned out to be one of the lines running to my MBC... it can be a tedious process but inspect every single line as there may be several...
    6. Replies
      5
      Views
      255

      The oil and coolant banjos are different from...

      The oil and coolant banjos are different from each other but both oil ends are the same and both coolant ends are also the same. What bits do you need?
    7. Agreed - these belts are pretty tough and don't...

      Agreed - these belts are pretty tough and don't break without serious persuasion. I was running mine for a while like this until I noticed it...
      ...
    8. Replies
      3
      Views
      263

      It will be tight but, assuming you have the right...

      It will be tight but, assuming you have the right belt, it will fit... try pulling the belt half way off at the cam so there's less angle on the belt while you get it started at the crank end.
    9. Replies
      3
      Views
      261

      http://www.dieselgeek.com/VW_and_Audi_Short_Shifte...

      http://www.dieselgeek.com/VW_and_Audi_Short_Shifters_s/1830.htm
    10. Great DIY - thanks Gabe & everyone else who's...

      Great DIY - thanks Gabe & everyone else who's contributed. I installed an 02M from a TT 225 into my GLI today by myself... I was expecting a struggle but it popped right into place. Here are a couple...
    11. Replies
      6
      Views
      454

      I'm interested in this too as I'll be installing...

      I'm interested in this too as I'll be installing a used centre driveshaft shortly... keep us posted.
    12. Ah, here's what I have... ...

      Ah, here's what I have...

      http://store.034motorsport.com/check-valve-1-8t-2-7t-aan-pcv-billet.html
    13. This what you're looking for? ...

      This what you're looking for?

      http://www.performancebyie.com/integrated-engineering-billet-block-breather-adapter-for-1-8t-mk4-2-0l
    14. Replies
      25
      Views
      1,156

      Nice work. I had two springs mounted like that on...

      Nice work. I had two springs mounted like that on my last turbo and the one closest to the hot-side broke after a while - so depending on how much heat the spring is catching, you may want to protect...
    15. Hey Mooseman - welcome aboard and congrats on the...

      Hey Mooseman - welcome aboard and congrats on the Passat!

      The 16 valve and 20 valve pistons are a little different as the 20v piston has a third exhaust valve relief... your best bet will likely...
    16. Replies
      25
      Views
      1,156

      Looks like you could hook two spring together and...

      Looks like you could hook two spring together and then loop around the back of the canister and down to the actuator arm...
    17. Replies
      919
      Views
      87,496

      Funny - I was just thinking about this today......

      Funny - I was just thinking about this today... my exhaust is apart and the S4 clamp I was using bent the aluminum muffler a little out of round. Good idea with the slip fit connection :thumbup:
    18. Poll: I'd be inclined to quiz the seller on the alloys...

      I'd be inclined to quiz the seller on the alloys used in the housing as well as machining tolerance specs and see how he responds. Considering how many things are outsourced, this housing could be...
    19. Good question - I was wondering this myself.

      Good question - I was wondering this myself.
    20. Replies
      16
      Views
      658

      Or just buy direct from... xs-power.com

      Or just buy direct from... xs-power.com
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4