Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: zoidmk5

    Page 1 of 13 1 2 3 4

    Search: Search took 0.22 seconds.

    1. Replies
      16
      Views
      676

      the number in the clutch name (350 in FX350)...

      the number in the clutch name (350 in FX350) refers to the torque it can handle...that should get you started. there is clutchmasters, competition clutch, southbend, on and on, and everyone is going...
    2. Replies
      6
      Views
      221

      trans should be fine, ECU has no control over the...

      trans should be fine, ECU has no control over the trans...you'd have to look into the differences between the B5 and B6 harness and ECU, since it controls your gauges and what not that are obviously...
    3. Replies
      6
      Views
      221

      shouldn't be much difference at all between the...

      shouldn't be much difference at all between the two motors, so your current harness and ECU should be fine. worst case, you have to swap a few things that may be different on the accessory side, VVT...
    4. who else would tune Lugtronic other than...

      who else would tune Lugtronic other than Lugtronic/Lugnuts/Kevin Black???
    5. I wouldn't have changed a thing. built the...

      I wouldn't have changed a thing. built the exhaust and intake manifolds I did, got the PT5858 turbo I did, ID1000, Tuscan rods, stock piston, Lugtronic, Wavetrac, FX400...not a single regret
    6. Replies
      107
      Views
      31,563

      it was an old shot

      it was an old shot
    7. Replies
      107
      Views
      31,563

      this car was completely dismantled a few years...

      this car was completely dismantled a few years ago and sold off
    8. Replies
      5
      Views
      293

      just port the small port flange on the manifold...

      just port the small port flange on the manifold out to AEB spec. RMR uses the same size runners, so there is def. room to remove some material for your needs
    9. Replies
      3
      Views
      216

      updating this from forever ago. a few days after...

      updating this from forever ago. a few days after making this post, I fixed any and all problems. I went ahead and replaced/updated the crack pipe with an aluminum one, and new thermo housing and CTS....
    10. to install the studs, there is a female hex in...

      to install the studs, there is a female hex in the top of the stud that you hand tighten into the block, pop on the head, then torque the nuts down, removal is the reverse process. follow the same...
    11. whenever you have the opportunity to do so, which...

      whenever you have the opportunity to do so, which is right now, put in studs. they will handle over double the power you are planning on putting down, and they have rolled threads, not cut like...
    12. the diagram shown could work, however I would do...

      the diagram shown could work, however I would do it without check ball valves.

      __ _8_________inline_______
      :) Y :):):):):):):):):):) i
      :) i :):):):):):):):):):) i...
    13. I don't see you needing an 044 in an all motor VR...

      I don't see you needing an 044 in an all motor VR Tim. I also don't see a mostly stock VR being able to handle a large enough shot of nitrous that would require such an extreme increase in fuel....
    14. Replies
      4
      Views
      168

      all drivers side (LHD) manifolds are small port,...

      all drivers side (LHD) manifolds are small port, but can be opened to large port, or use one of those phenolic transition spacers
    15. Replies
      4
      Views
      168

      bump

      bump
    16. Replies
      4
      Views
      168

      FS: TT 225 manifold

      I bought this quite a few years ago. had it powder coated matte chrome and installed new injector cups. has only been mocked up, has not been on a running engine since coating. $250obo

      SOLD
    17. Replies
      3
      Views
      216

      coolant temp question

      i have a 2003 GLi 24V VR. i did the fan test and know that i am having issues with my fans in general and know that i need to replace them. my question is, even if my car is at the proper temp, 190...
    18. Replies
      56
      Views
      2,661

      that was one of my initial thoughts...glad you...

      that was one of my initial thoughts...glad you got it worked out
    19. would be nice to see some logs to see when/if...

      would be nice to see some logs to see when/if there is fuel cut, if spark is maintained up to WOT...could be something as simple as the plugs not having enough life left to produce the spark needed...
    20. Replies
      7
      Views
      707

      in a separate surge tank like the IE...many...

      in a separate surge tank like the IE...many people, including myself, buy just the face/mounting plate, and weld that into their own custom surge tank, or even into a fuel cell
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4