Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Nevaeh_Speed

    Page 1 of 13 1 2 3 4

    Search: Search took 0.25 seconds.

    1. Replies
      4
      Views
      666

      I have 2 vr6 CA swaps. Both passed. What...

      I have 2 vr6 CA swaps. Both passed. What readiness code is not setting? And I think yellow is the L line, which nobody uses as the K what most readers use to communicate.
    2. Interesting... is the 044 loud like 255 Walbro....

      Interesting... is the 044 loud like 255 Walbro. And is it that bad to really go through all that work?
    3. Replies
      2
      Views
      485

      I'm running DRC 268's. Great mid-range and top...

      I'm running DRC 268's. Great mid-range and top end. Haven't heard anything on the camshafts you mentioned.
    4. Replies
      2
      Views
      442

      Not possible, it's more like you have the gear...

      Not possible, it's more like you have the gear shift adjustment wrong. Since you have no reverse or 1st that kind of explains it all. Do an shifter alignment.
      ...
    5. Sent you a PM

      Sent you a PM
    6. Not like you did. And if was a direct change over...

      Not like you did. And if was a direct change over the car should have ran on the first try. What didn't he change over or tried to use from the obd1 engine?
    7. Replies
      5
      Views
      1,114

      Haven't talked to Mr. Black in awhile but also...

      Haven't talked to Mr. Black in awhile but also haven't had the need to. But I suggest sending him an email.
    8. So to make sure I get this. You swapped in a obd1...

      So to make sure I get this. You swapped in a obd1 motor into a obd2 car and want to use the obd1 harness in said obd2 car. Does that sound right?
    9. Replies
      4
      Views
      832

      Same head besides the camshafts and covers. Will...

      Same head besides the camshafts and covers. Will work just fine if you use your old parts. Also the afp headgasket is better than the aaa. bumps compression up a tad.
    10. So I assume you have the mk3 oem intake manifold?...

      So I assume you have the mk3 oem intake manifold? If you get baseline #'s from a oem manifold turbo car it's gonna be off, as the turbo nukes the inlet flange area of the oem manifold.
    11. Man this thread needs some updating. Got more...

      Man this thread needs some updating. Got more toys, and lots of boost.
    12. Replies
      9
      Views
      939

      So if the fuel pump has direct power does the car...

      So if the fuel pump has direct power does the car run?
    13. Replies
      2
      Views
      646

      g31 = map sensor. Could be bad, or wrong one for...

      g31 = map sensor. Could be bad, or wrong one for the program, early 1.8t needs late, or vise versa. But I would start there, check block value vs. actual gauge.
    14. Replies
      2
      Views
      576

      try a higher psi cap .

      try a higher psi cap .
    15. So a few months back my OEM pedal setup started...

      So a few months back my OEM pedal setup started feeling funny (low engagement), so I pull the clutch slave and the tip had split into two. So I decided to re-install the metal setup, only thing I...
    16. 13 dollars and a smartphone can read and clear...

      13 dollars and a smartphone can read and clear codes.
    17. Replies
      21
      Views
      1,294

      DLRE, Dustin Lee Racing Engines in Lancaster, CA....

      DLRE, Dustin Lee Racing Engines in Lancaster, CA. Dude is super smart and races dragsters as a hobby. Build all kinds of crazy motors.
      ...
    18. Replies
      2
      Views
      458

      Always run the correct o2 sensors with a swap for...

      Always run the correct o2 sensors with a swap for oem engine management unless your using standalone.
    19. PM'd

      PM'd
    20. Replies
      3
      Views
      657

      had the 034 rail, it's a tad bulky. Running a...

      had the 034 rail, it's a tad bulky. Running a MigFab manifold and rail now, plus it come with brackets.
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4
    Back