Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: animaniac

    Page 1 of 13 1 2 3 4

    Search: Search took 0.77 seconds.

    1. Before you do anything else, try some electrical...

      Before you do anything else, try some electrical contact cleaner on the vss terminals and wiring connector, let it evaporate off before reconecting, you should disconect the battery before doing...
    2. Yes that should be it, but you may have a vehicle...

      Yes that should be it, but you may have a vehicle speed measuring block in the engine module or the intrument module, i'm sure i've seen one when messing around.

      Coding
      000?x: DSP Mode (Dynamic...
    3. Replies
      1
      Views
      255

      16505/P0121 - Throttle Position Sensor (G69):...

      16505/P0121 - Throttle Position Sensor (G69): Implausible Signal

      Possible Symptoms
      MIL on
      Poor engine performance

      Possible Causes
      Wiring Harness issue
      Failed Throttle Body
      Failed ECM
    4. Replies
      1
      Views
      246

      Please post an autoscan.

      Please post an autoscan.
    5. The way i've bled the slave cylinder is to use a...

      The way i've bled the slave cylinder is to use a bleed hose with a one way valve in it, but even then when you pull the clutch pedal up it sucks the air back in.

      The best way is to close the bleed...
    6. 1st gear rattle, caused by reverse gear spring, can this be replaced without box removal

      After doing some research my gearbox is rattling in 1st gear only and by looking at a topic by user name the kevin,...
    7. Replies
      9
      Views
      1,113

      My mk4 1.8t is making the same noise in 1st, but...

      My mk4 1.8t is making the same noise in 1st, but it only does it under acceleration, the noise goes if i take my foot off the accelerator, sounds like the gear is chipped but if that was so it would...
    8. Replies
      13
      Views
      3,640

      Sounds like a good plan, just make sure the parts...

      Sounds like a good plan, just make sure the parts are clean and make sure the surface is smooth and when spraying ''primer'' ''paint'' or clear coat make sure the cans are well shaken and keep the...
    9. Replies
      10
      Views
      2,425

      I'm pleased it was just worn out fluid. I'm...

      I'm pleased it was just worn out fluid.

      I'm pretty sure a garage would just throw a new pump on, complete with new fluid and hey presto steerings fixed! at a cost.

      Yet the same results for just...
    10. Replies
      10
      Views
      2,425

      The pump could be on it's way out, so before...

      The pump could be on it's way out, so before replacing the pump or salvaging a 2nd hand one, try changing the steering fluid.

      Use Central Hydraulic Fluid pentosin chf 11s is what it's called and...
    11. Replies
      2
      Views
      969

      http://wiki.ross-tech.com/wiki/index.php/03271 ...

      http://wiki.ross-tech.com/wiki/index.php/03271

      03271 - Installation of Positioning Motor for Back Pressure Flap
      Possible Causes
      Positioning Motor for Back Pressure Flap (V71) not installed ...
    12. 17551/P1143/004419 - Load Calculation Cross...

      17551/P1143/004419 - Load Calculation Cross Check: Upper Limit Exceeded
      Possible Solutions
      Check Mass Air Flow Sensors (G70)
      Check Throttle Pedal
      Check Throttle Pedal Position Sensor...
    13. Replies
      2
      Views
      1,683

      Well the tip of the plug is clean so it's not...

      Well the tip of the plug is clean so it's not coming from the cylinder.

      Possibly coming from your the rocker cover and seeping down into the spark plug hole.

      If your under warranty i'd get the...
    14. I think my haynes manual said that it just slides...

      I think my haynes manual said that it just slides on, and that you should push it on using the inner race of the bearing.

      Although i just pushed it on, because there was no resistance and it...
    15. Replies
      12
      Views
      949

      That is what i'd do much easier than messing with...

      That is what i'd do much easier than messing with your headlining and routing the wire to the head unit.
    16. Replies
      6
      Views
      1,076

      Has anyone had their haldex diff blow up.

      Vw diff's are known for blowing the rivets, pinion shafts and roll pin.

      On the 4wd vw's has anyone had their front or back diff blow up?

      I'm probably going to buy an R32 but i'd just like to...
    17. Replies
      6
      Views
      1,076

      Well vw's are know for the diff's blowing up! ...

      Well vw's are know for the diff's blowing up!

      Any kind of grinding noises from the front of a vw makes the owners shake in fear that the differential has gone!:eek:

      But i've never had a diff...
    18. Replies
      2
      Views
      774

      I had to think then, i thought it was driven by...

      I had to think then, i thought it was driven by the output shaft inside the box but on remembering theres a gear on this diff.

      Heres a pic
      ...
    19. Thread: Car Speakers

      by animaniac
      Replies
      1
      Views
      273

      Well the alpine are louder at 300w but the...

      Well the alpine are louder at 300w but the frequency response is from 65 hz where as the jl are 100watts but they lave a lower 59 hz frequency response.

      Both have statements like gives thunderous...
    20. The no.1 small hose goes from pancake pipe to...

      The no.1 small hose goes from pancake pipe to intercooler and the no.2 hose goes from the turbocharger outlet to the metal L shaped pipe which bolts to the back of the engine and this leads to the...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4