Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: ps2375

    Page 1 of 13 1 2 3 4

    Search: Search took 0.46 seconds.

    1. Replies
      8
      Views
      467

      Troubleshoot the no spark problem. Is that no...

      Troubleshoot the no spark problem. Is that no spark w/ ABA ecu or w/ MS? Either way, you have a wiring issue to find.
    2. Replies
      8
      Views
      467

      If you don't have lights, you prolly don't have...

      If you don't have lights, you prolly don't have power to the ecu. Have you checked that? And if you have power to relay and no power to ecu, the relay will turn on as the ecu is not controlling the...
    3. Thread: Ac compressor

      by ps2375
      Replies
      17
      Views
      669

      If the clutch has power and it is not engaging,...

      If the clutch has power and it is not engaging, it's the clutch. If all else is good and the clutch has no power, then you need to look at the AC control module mounted on the underside of the...
    4. Replies
      22
      Views
      885

      The windage tray is not plastic, the small baffle...

      The windage tray is not plastic, the small baffle attached to the oilpump pickup is.
    5. Replies
      84
      Views
      9,619

      RUG, not carpet....LOL. Was prolly on sale too.

      RUG, not carpet....LOL. Was prolly on sale too.
    6. Replies
      22
      Views
      885

      And what was water temp doing during all of this?...

      And what was water temp doing during all of this? And oil press warning lite?
    7. If you have a center mount carb, you will still...

      If you have a center mount carb, you will still need the heat to the manifold, otherwise the fuel will fall out of the air stream as it goes from vapor to droplets.
    8. Thread: Aba cog pulley

      by ps2375
      Replies
      5
      Views
      303

      what do you expect from a powered metal...

      what do you expect from a powered metal forging/casting? Maybe you are luck that is what failed on your 8K rpm/500whp ABA.....:screwy:
    9. Ignore the marks on the sprocket. Set the dist to...

      Ignore the marks on the sprocket. Set the dist to #1 TDC and also the crank and cam and put the belt on. Done. The mark is there and valid only IF the dist is installed when the sprocket is aligned...
    10. Maybe your first purchase should've been a Bently...

      Maybe your first purchase should've been a Bently Manual. Then you don't have to post in a forum to beg for information.:facepalm:
    11. That only really matters IF the dist is installed...

      That only really matters IF the dist is installed in sync with the shaft/sprocket. If you look in the Bently manual, it tells you how to set the sprockets, and you can align them then install the...
    12. Replies
      84
      Views
      9,619

      All I have to say is ....Wow. nice job.

      All I have to say is ....Wow. nice job.
    13. Replies
      6
      Views
      425

      I would suggest getting a wideband O2 sensor...

      I would suggest getting a wideband O2 sensor installed and using that to help tune. It may only need small adjustments or you might only need to get the timing worked out. The vacuum adv should be on...
    14. Replies
      6
      Views
      425

      For an idle jet, maybe a somewhere in a 40-50...

      For an idle jet, maybe a somewhere in a 40-50 range. Venturi size will depend upon where you want the majority of the power band to be, the mains and airs go from there. What cam and CR does it...
    15. Nice to know Buggyman. And as it does have the...

      Nice to know Buggyman. And as it does have the the rear bumper(always will), that will help keep it stabilized also.
    16. You can if you have the tool, same as for doing...

      You can if you have the tool, same as for doing cam bearings in an OHV motor, I'm told.
    17. :what::confused: :confused: ...

      :what::confused: :confused:

      Is this your first motor rebuild? You might be able to find a shop that can do them as a short/long block, but the motor will need to be pulled.
    18. Were the IM shaft bearings replaced? Those are a...

      Were the IM shaft bearings replaced? Those are a major culprit for low oil pressure. And what weight oil?
    19. Yes, I have been thinking about a remove-able...

      Yes, I have been thinking about a remove-able apron. I have only had my Bug for about 8 months, it was my father's car and he had it parked for about 20yrs(and he's not dead), I have just had it on...
    20. When I was re-installing the motor in my Bug, I...

      When I was re-installing the motor in my Bug, I spent an hour and a half trying to get the motor slid onto the input shaft. I had cleaned the trans and the disc was new, the next day after sleeping...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4