Search Results - Vortex Media Group
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: madonion

    Page 1 of 13 1 2 3 4

    Search: Search took 0.20 seconds.

    1. Replies
      2
      Views
      137

      I'm not sure if the oil pump is bad yet. It may...

      I'm not sure if the oil pump is bad yet. It may be weak, testing with the high pressure switch I have 23psi+ from 1900RPM I just don't know the exact number yet. I have a sound that resemble pinging...
    2. Replies
      2
      Views
      137

      frankenstein oil pump

      I have two oil pumps, one from a vr6 2.8L bdf 2003 and the other from a 3.2L BMX 2005. I'd like to take the pickup part of the pump from the 2.8 pump and put it on the 3.2L oil pump. The pumps look...
    3. Replies
      4
      Views
      173

      After the flow rate test I've got the following...

      After the flow rate test I've got the following results 650ml @ 11.80V @ with 3Bar regulator I believe this is within specs. That's 78LPH @ 11.80V I estimate that would be arround 85LPH@13.00V
      ...
    4. Replies
      4
      Views
      173

      According to the bentley repair manual, with 12V...

      According to the bentley repair manual, with 12V the pump should have a minimum flow rate of 625ml/per 30 second and that is a flow rate of 75LPH.

      For single fuel pump the minimum would be...
    5. Replies
      4
      Views
      173

      That's the highest number I've seen so far. From...

      That's the highest number I've seen so far. From what I understand that number is for Anun china made pump. Mine is relatively new but I have doubts about it being able to supply for 260hp. When I'm...
    6. Replies
      4
      Views
      173

      G60 Early inline fuel pump lp/hr

      Hey guys I've been looking arround to find the lp/hr of the ealry inline fuel pump found on the g60, BOSCH part number is 0 580 453 914. I've seen different informations, there's some informations...
    7. Replies
      9
      Views
      633

      Short term fuel trims is block 033 and long term...

      Short term fuel trims is block 033 and long term 032. What size FPR are you running right now ?
    8. I'm looking at some logs right now I'd really...

      I'm looking at some logs right now I'd really like to know if I see the ignition timing is at 15.8 degrees and I get a CF of 15 does it mean the ECU was asking for 30.8 degrees of timing ? I really...
    9. Here's what I know, you need to plug the Evap...

      Here's what I know, you need to plug the Evap solenoid among other things to get long fuel trims to adapt.

      You can't really use the 2.8L TB unless you make a custom adapter plate for the 3.2L...
    10. I was pming this to a fellow vertexer and decided...

      I was pming this to a fellow vertexer and decided to post this here also

      I've been having the issue since 2012, that's the year I did a vr6 24v swap into my corrado. The pinging issue as prevented...
    11. negative long term mutliplicative fuel trims

      Will a missing post-cat o2 sensor drive fuel trims negative ?
      Will high IAT drive fuel trims negative (140F) ?

      my Idle fuel trims are -1.7 and my part throttle fuel trims are -17.2 (Block 032)
      ...
    12. Replies
      0
      Views
      200

      MAF and fuel trims

      When MAF is disconnected or when there's a code related to a bad MAF stored on the ECU, is it normal behavior for long term fuel trims to go full negative ? like negative -27.
    13. Replies
      56
      Views
      4,963

      What is the reason for keeping the combie valve ?...

      What is the reason for keeping the combie valve ? Are you located in a place where emissions rules are really strict ?
    14. Replies
      3
      Views
      764

      Well I might be wrong about the 6* of advance....

      Well I might be wrong about the 6* of advance. Since the MAF is only slightly larger porpotionnally to the engine displacement 2.8L vs 3.2L and 2.75inch ID for MAF and 3inch ID. I believe the engine...
    15. Replies
      3
      Views
      764

      I finally got my car running, I wanted to let you...

      I finally got my car running, I wanted to let you know a bigger MAF will also advance timing. I'm going to try to remove 6* of timing with unisettings to see if things run better.
    16. Replies
      2
      Views
      367

      Drilling the socket might be the most intresting...

      Drilling the socket might be the most intresting idea money wise if it's possible to drill in tool steel. Should I get an impact socket or a regular socket if I plan to drill and weld ?

      Should...
    17. Replies
      2
      Views
      367

      Vibration damper torquing

      I'm trying to torque down my engine vibration damper. The engine is acting as a spring preventing me to apply torque in a safe maner. Is there a way to torque these things down whitout the special...
    18. Replies
      19
      Views
      713

      The swap is complete, it ran for a good 3 years....

      The swap is complete, it ran for a good 3 years. I'm putting a 3.2L BMX in place of the BDF. While disassembling I found that the lower rad hose had been leaking a little coolant. Since I cant find a...
    19. MK4 plastic coolant valve (lower radiator hose) fit corrado radiator ?

      Hey guys,

      Does this type plastic coolant valve found on MK4 fit on corrado radiator ? As anyone tried it ?

      http://www.agthompsonfamily.com/vw/WaterPump16.jpg
    20. Replies
      19
      Views
      713

      MK3 thermostat housing might change my other...

      MK3 thermostat housing might change my other hoses too much I wonder if the hose from a mk4 12v vr6 would work particularly the plastic part that connect to the rad. To these fit on our radiators ?
      ...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4