Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: Currancchs

    Page 1 of 13 1 2 3 4

    Search: Search took 0.71 seconds.

    1. I understand, sounds good. Right now I have a...

      I understand, sounds good. Right now I have a bootmode/bench harness set up. A Galletto clone, a Ross-Tech Hex USB, Winols 2.24, MPPS, Tuner Pro, Ultima (Checksum Corrector), Nefmoto Flashing...
    2. Hi there, I was finally able to get the flash...

      Hi there, I was finally able to get the flash image and EEPROM image off of the stock ECU, I could send them to you to have a look at, but if you would feel comfortable (and so inclined) posting the...
    3. OK, sorry it took so long to post back here, but...

      OK, sorry it took so long to post back here, but the problem seems resolved for now. I got some new plugs and gapped them to 0.028'' and that seemed to be all it needed. The new plugs are NGKBKR7E's,...
    4. Well, I have been doing quite a bit of reading...

      Well, I have been doing quite a bit of reading lately on how to go about this, but still don't have the file off of the ECU! I made a bench flashing harness that works just fine, but I am still...
    5. Thanks! I don't know how I missed that, I'm on...

      Thanks! I don't know how I missed that, I'm on that forum as well, same username.
    6. Haven't had a chance to really check out the...

      Haven't had a chance to really check out the vehicle, but did find one issue and some interesting information.

      The hose on the high pressure side of the DV had slipped and was only partially...
    7. Replies
      22
      Views
      1,062

      I put a SPEC Stage I with a 13 lbs. steel...

      I put a SPEC Stage I with a 13 lbs. steel flywheel (lightest I could find without going aluminum) on mine a while back (~25k miles). To be honest, it doesn't allow the car to rev that much quicker,...
    8. Good questions. The fuel trims had been reset...

      Good questions. The fuel trims had been reset just the day before this happened, but were less than +5% (don't remember exactly) about a week ago. I may not be able to get the current fuel trim info...
    9. Thanks for the advice. I will return it back to...

      Thanks for the advice. I will return it back to stock until the problem has been resolved. I originally increased the pressure a bit because I had been monitoring injector duty cycle and it was over...
    10. I have been and am continuing to do research into...

      I have been and am continuing to do research into this issue. But, I am not seeing the wideband go lean under hard acceleration. In higher gears the vehicle is richening up quite nicely, and in lower...
    11. I don't have a vacuum style boost guage, but have...

      I don't have a vacuum style boost guage, but have been using a LiquidTT, which allows Vag-com style reading of boost request and actual boost in real time. I am getting a requested boost of about 21...
    12. 2001 225 TT Fuel Cut in Lower Gears w/out code?

      Hi guys, I have an odd issue and don't even know where to start...

      The vehicle is a 2001 Audi TT 225 Quattro 6 speed with the following modifications:
      Adjustable FPR (Set at 42 psi @idle with...
    13. Anybody have the definition file for an '01 AMU 225Q TT (ECU: 8N0 906 018T)

      Looking to delete the rear O2/SAI from a spare ECU, but am just learning about this, and don't yet have the experience to create my own definition file. If anybody has one in a tunerpro or winols...
    14. Replies
      6
      Views
      3,823

      When I pulled my transmission off there was some...

      When I pulled my transmission off there was some surface rust on the trans input shaft. I had cleaned off the old lube, but never relubricated. Rust formed and the clutch disc was unable to slide...
    15. Replies
      238
      Views
      26,857

      Thank you for the detailed and quick response! ...

      Thank you for the detailed and quick response!

      I was actually aware of the resistor trick, but luckily my car doesn't actually throw any codes related to the SAI being unplugged (I left the...
    16. Replies
      238
      Views
      26,857

      Car looks awesome! Don't mean to hijack this or...

      Car looks awesome! Don't mean to hijack this or anything, but curious as to how you're getting around the CEL for removal of the SAI system. I removed mine a while back and love not having the hoover...
    17. Replies
      14
      Views
      1,804

      I believe stock is a "C" (that's what my car had...

      I believe stock is a "C" (that's what my car had on it when I bought it), but the new equivalent is a "F" (according to the local dealer), which is what I am running currently. I had a "K" on there...
    18. Replies
      379
      Views
      64,471

      Thanks for the tip Max! Used one of the small...

      Thanks for the tip Max! Used one of the small Home Depot springs in the two-pack with large and small springs (~5 lbs.) on my '01 AMU 225 TT w/APR Stage 2. Went from peaking @~18.5 psi and holding 14...
    19. Hello kTTang, I understand your concerns and hope...

      Hello kTTang, I understand your concerns and hope that we can get the unit to work for you. I didn't make any modifications to the unit, it just sort of worked right of the bat for me. My car is an...
    20. Replies
      18
      Views
      2,203

      After installation of the 034 motorsports AMU...

      After installation of the 034 motorsports AMU silicon breather system, my problem seems to be resolved. The stock breather system seemed to flow pretty freely, though, although I forgot to check the...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4