Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: ryan mills

    Page 1 of 13 1 2 3 4

    Search: Search took 0.45 seconds.

    1. In the police state of VA, I keep it under 80 on...

      In the police state of VA, I keep it under 80 on the interstate. On the way to work, the speed limit is 70, so I keep it around 72-75. If I'm driving my A4, I stay close to the limit, since the car...
    2. I have an AEB engine, and run a larger passat v6...

      I have an AEB engine, and run a larger passat v6 throttle body without issue. As long as it plugs in, I don't think it would be any different. I would try doing a throttle body adaptation with...
    3. If you're starting from scratch.... I was able to...

      If you're starting from scratch.... I was able to get the correct voltage tables for the siemens/deka injectors, 830cc....
    4. Replies
      98
      Views
      7,414

      FV-QR

      I miss mini trucks, and being able to get a truck or small car with 0 options, not even a radio. I remember when my dad bought a new F-150, no rear bumper. He bought one after a couple weeks or so,...
    5. FV-QR

      One big step forward.... the CORRECT injector battery compensation numbers for my injectors. Runs better, tons left to do.
    6. Replies
      6
      Views
      270

      pull the piping off your intercooler, clean out...

      pull the piping off your intercooler, clean out the oil, and reassemble. check for oil accumulation again after driving.
    7. I was going through my subscriptions and saw...

      I was going through my subscriptions and saw this..... I agree on the 303 stuff, it's expensive and sometimes hard to find, but it's pretty good stuff. If you want something cheaper and decent, I...
    8. FV-QR

      The n80 evap solenoid has a similar connector, not too sure if it's possible to mix the two or not. On my 1.8t, they are also pretty close together on the harness, but it is an entirely different...
    9. lucky!!!!!:thumbup::thumbup::thumbup:

      lucky!!!!!:thumbup::thumbup::thumbup:
    10. Fine damn question! Eurodyne specifies that...

      Fine damn question!

      Eurodyne specifies that the 077 133 471 JX MAF must be used in the read me file, but it would be nice to know the differences.
    11. Replies
      13
      Views
      410

      your belt might have a few teeth chewed off....

      your belt might have a few teeth chewed off. that's all it takes.

      or maybe the chain tensioner inside the valve cover ate it, who knows.... either way, it sounds like it's time to start that...
    12. Replies
      42
      Views
      40,640

      Sticky: How about I elect..... me?!?

      I haven't made any build threads yet, been too busy scrambling to put it together....

      * Chassis: 1999.5 A4 Quattro manual sedan
      * Turbo: Garrett GTX2867R
      * Displacement: 1784cc
      * Software:...
    13. Replies
      6
      Views
      270

      Do you have a manual transmission, and did you...

      Do you have a manual transmission, and did you pull up to an intersection with your car in gear? The higher vacuum when decelerating can pull oil from the valve seals if they're worn.


      If it...
    14. They do, I've been fiddle-phucking with it for a...

      They do, I've been fiddle-phucking with it for a few days now.... I made a big step in the right direction getting new voltage compensation numbers for the Siemens-Deka 830cc injectors I've been...
    15. Pretty much my man! Just have some beer and...

      Pretty much my man! Just have some beer and bandaids handy when you swap it out. -Oh, if for some reason the downpipe doesn't quite reach, just add a little to a straight section of pipe behind it.
    16. Any info out there on how to use Eurodyne Maestro to tune an AEB?

      I've tried looking at the unofficial guide and whatnot, but it's so big, I can't seem to find any of the information I need. The DBC cars are a completely different animal, and I really don't know...
    17. Replies
      2
      Views
      195

      yeah, doesn't look like the rear main, but since...

      yeah, doesn't look like the rear main, but since you're in there...... I'd go through the PCV stuff in front of the oil filter housing, and also check the oring sandwiched between the oil cooler and...
    18. hold off on that battery!!!! It doesn't like cold...

      hold off on that battery!!!! It doesn't like cold weather..... Also, it's just enough power to crank the 1.8t, I don't know if it could turn over a larger engine.
    19. I wouldn't think that iron block would really be...

      I wouldn't think that iron block would really be an issue.... Now, if someone re-used the head bolts/studs or incorrectly torqued the gasket, that might have been an issue. When the coolant temp...
    20. So here's a couple pics..... I grabbed the...

      So here's a couple pics.....

      I grabbed the GREEN/LAVENDER from pin 11 on the ECU, and pulled it harness at the Tee where it splits to go to the injectors and cam sensor.
      ...
    Results 1 to 20 of 250
    Page 1 of 13 1 2 3 4