For Sale- Wanted To Buy Thread

[yellowslc]

Please only post for sale and wanted to buy items in this thread. They must be related to carbs/itbs/SEM's, all others will be deleted.

Robert

[VWHESS]

WTB: 16v carb setup or any parts to put one together

[MadBubba]

F.S weber 45's dcoe (used)

off of a 16v
45 DCOE 152
Part Number : 19600.060

$650can.

http://www.mgexperience.net/article/45dcoe.html

[VRT]

selling just the itbs, flange for the itbs and trumpets
all you need is the lower intake
asking $500

http://usrallyteam.com/itb.html
USRT sells these for $1000

Modified by VRT at 1:47 PM 8-21-2006

[Speed Racer.]

It's great this was finally made. I am needing GSXR 1000 TBs.

[littledevilo63]

will anyone have a sem setup for sale in about 2 months

[CortezVW81]

please tellme u still have the weber setup if soo email me at cortez08@gmail.com

[thumpergtivw]

I still have a weber setup for sale 40 mm 8v counterflow

[thumpergtivw]

lynx single sidedraft counterflow dcoe manifold 160 shipped in us

[kleingti]

I have 2 brand new 40 dells.with new manifold and special water outlet has k&n filters,all gaskets and such for install. 750. If interested, kleingti@hotmail.com

[MorpheusMac]

I'd love to snag a set of 16V throttles....50mm range?


Modified by MorpheusMac at 7:55 AM 6-28-2007

[VTFuturaYellowGTi]

Looking for a complete set up for a 8v cis or 16v crossflow

[SUSPENDED]

$1200 obo

sk dcoe 40mm sidedrafts used, rebuilt
long manifold (Rolands?) new, port matched
electromotive hpv-1 used
b.b. distro block off plate new
balance with 60-2 ring installed used
filters k&n used
abf coolant bit new
gaskets and other bits new

no: throttle linkage, ignition wires, horns

[diddle.]

I have a pair of webers and a manifold, plus a broken vac advance distributor. Building a different motor for the car now. I have a built 2.1l 16v I would like to sell also.

http://www.ebay.com/itm/VW-16v-Dual-...7c6ebe&vxp=mtr

[hantonyc]

found what i needed, thanks

[hantonyc]

saab dizzy(rebuilt) + new cap and rotor
msd blaster 2 high vibration coil
spark plug wires
icm

looking to get 140$ shipped. by PM please.

[fredybender]

WTB megasquirt or other standalone to drive waste spark coils (4) and external trigger on my carbed 16v, pm please !

PM'd (Megajolt lite JR) with everything needed

[kalvinlk]

1998 GSXR 750 ITB spacers, lasercut aluminum. $25 shipped to your door.

I have two available immediately, and can make more. These are lasercut aluminum spacers to space the throttle bodies 88mm apart, which is the spacing for 16v intake ports. All you need to do is have a shop weld on some extensions on the actuators, because when you space the throttle bodies apart, the levers are not long enough to actuate the next throttle body in line.

These were designed for my '98 GSXR 750 throttle bodies, and may/may not work on other GSXR bodies. You can get higher resolution images by following these links:

http://hobbez.net/gallery2/mai...ber=1
http://hobbez.net/gallery2/mai...ber=1

Here are some thumbnails, the top piece is the stock Suzuki spacer.

Modified by kalvinlk at 5:53 PM 8-16-2006


Modified by kalvinlk at 9:49 PM 8-18-2006

[silvervdubs99]

here we have a aeb intake flange/on piece runner set-up machined froma solid piece of 6061....just needs runners welded on it...i'll take 200 shipped



Modified by silvervdubs99 at 9:26 AM 8-22-2006

[rollercoasterracer]

Found


Modified by rollercoasterracer at 1:41 PM 8-22-2006

[kalvinlk]

edited: sold the TB's. Still have one bracket left though.


Modified by kalvinlk at 9:49 PM 8-18-2006

[machschnelGTI]

I am moving up to a class that allows Fuel injection, so I don't need these any more. These were purchased brand new from Weber about 1 year ago. They are OER 47mm carbs, which share all the parts with webers, and they're made in Japan. These carbs have been very good to me. They have less than 1000 total miles on them since new. Included in the package:

2 OER 47mm sidedrafts
Ported Rowland Manifold
Custom made linkage
Carter Fuel pump
Mr. Gasket regulator
Autometer fuel pressure gauge
The carbs have 42mm chokes in them right now, but I have a spare set of 40mm chokes that will be included in the sale, and a box full of jets and EM tubes

For all this, I'd like to get $1100

I also have an MSD programmable timing computer, and MSD adjustable timing control (you can adjust your static timing with a knob on the dash) and an MSD 6A box. This allows you to use the stock 16V distributor, and tune your advance curve the way you want it.

I'd like to get $400 for this setup.....its all wired and ready to go.

Modified by machschnelGTI at 9:21 PM 11-12-2006

Modified by machschnelGTI at 5:42 AM 11-13-2006

Modified by machschnelGTI at 11:09 PM 12-25-2006

Modified by machschnelGTI at 8:52 PM 12-27-2006


Modified by machschnelGTI at 8:52 PM 12-27-2006

[MoGtheMooGle]

***SOLD***


Modified by MoGtheMooGle at 12:26 PM 11-1-2006

[silvervdubs99]

FS: 16v Dellorto 40 16v carb set-up with ignition system
all have almost NO miles on them:
-rowland 16v intake manifold with spacers and rubber vibration gaskets
-dellorto 40 carbs jetted and tuned for a 2.0 16v
-4 green uni filters
-saab 900 vac advance dizzy
-carter fuel pump
-all fuel lines
-msd 6al ignition

this set-up starts and runs great, only reason i am selling is because i have an insane ITB set-up waiting to go on the car and i need to buy an SEM system, so these must go
bolt this set-up on in an afternoon and rip away sounding all street-bike
asking for 1200 obo

PLEASE IM me if interested

[CortezVW81]

if u still have this setup you defintely have a buyer

[sellitsoon]

need one on the cheap to slap on a manifold i just picked up. weber or dellorto 40 please--IM me

[zcxerxes]

just one?

[raceonlyrabbit]

Quote, originally posted by sellitsoon »

need one on the cheap to slap on a manifold i just picked up. weber or dellorto 40 please--IM me

Now I need one weber dcoe 45 thanks sellit yes just one ! I have 32/36 dfev with redline mani for trade or sale .

[im_a_local]

FS: SdS programmable engine management, new in box, will send pics to email upon request . shoot an offer over this way

[Speed Racer.]

2002 GSXR 750 ITBs with everything (TPS, etc).

$150 shipped.

[the4ork]

WTB clean xflow ITB setup, bigger the better, have $ to play

[the12for12]

WTB

ANY and everything 8V (carbs, intakes, pumps, etc) applications, Udig?

Progressive, IDA, DCOE, DCNF, Dells, Mikis,... pretty much whatever you have, kool?

Holla back whenever via IM

Thanks,
Thomas

[the12for12]

WTB

8V intake manifold ASAP!!!!

DUAL Sidedraft application NEEDED

Thanks,
Thomas

[eojthekid]

WTB: cross-flow intake manifold for carb setup aba head [IMG][/IMG]

[skidplate]

sold


Modified by skidplate at 5:21 AM 12-12-2006