looking for a single side draft intake manifold for a counterflow VW engine. would take a dual carb manifold too if thats all i can get.
what do you guys have to offer?
if i get the right offer i might part with this.
this is a custom grant motorsport ITB setup for vr6.
rumored to be the only one in the US.
i dont need to sell it but im thinking about it.
you will get, custom length shorty lower intake manifold powdercoated chrome, chrome plated grantmotorsport manifold, GM TP sensor, 6 jenvey throttle bodys, fully polished, polished stainless steel hardware, polished throttle linkage, 6 staggard velocity stacks that are fully polished.
also thinking of selling my custom built MS system along with it. built by need a vr6, MS module, and harness.
this came off the mk3 race car from jersey.
i have alot of money in this, please dont lowball offer.
heres what it looked like when i bought it.
it WILL stick through your hood with a full length lower manifold.
fitment on my mk2, sits behind the grill just perfectly. even enough room to mount a screen filter to the grill like i did.
i might have a pic of the horns somewhere but ill have to look.
dont be fooled, this takes a good amount of custom modifying to get to fit right on a mk2, or to keep it under the hood anyway.
Modified by rhiGLi at 1:08 AM 1-22-2010
www.4everkustoms.com - polishing, chrome, copper, brass, POWDER COATING, and more!
top dawg 09 and 10eurotuner 1/07 pvw 2/10 eurotuner 5/12
I have for sale a carter 4070 fuel pump
Literally brand new still in the box, never had fuel ran through it. Bought it for another project that never came to fruition.
Jegs has it for 72.99 +shipping
I want to get 60.00 shipped.
Freshly rebuilt (tanked and rodded) 40 IDF Weber. Cleaned up very nicely. All gasketing surfaces have been trued.
Setup for dual (side by side) IDF's. Fuel ports ready to be taped for threaded in fuel fittings.
Come complete with Manual Choke, Air Filter, and Stacks.
$170 shipped (manifold not included)
Modified by WCHLVR at 2:14 AM 1-28-2010
Quote, originally posted by gitthatcrew » Looking to buy a 16v itb setup under 300 hopefully
ditto this man haha. price isnt so much an option as the fact that IDK what all i'm looking for
2008 Jetta 2.5 SE (daily)
1981 Rabbit Truck (project)
Quote, originally posted by JayEuro910 » ditto this man haha. price isnt so much an option as the fact that IDK what all i'm looking for
Well if it helps you or any im looking for the itbs, manifold, tps, and harness
Quote, originally posted by Issam Abed » Complete ITB kit for a 1.8 20V motor.
Kit comes with:
(4) Custom TWM 48mm ITB's with airbox
(2) Custom fuel rails + 8 injectors
(8) Additional injectors
(1) DTA E48 EXP standalone Engine management system with FULL HARNESS (allready mapped)
(1) Bosch Motorsport Coil pack + plug wires + all sensors
Asking $1700 USD for the lot.
(ITB's alone are worth 1800 USD)
You know wether or not this will work on a mk2 1.8 16v engine? For instance with nothing but a different manifold?
Even a weirder setup... you know wether or not this wil work on only one of two Audi V8 heads?
Quote, originally posted by Breadfan5968 » You know wether or not this will work on a mk2 1.8 16v engine? For instance with nothing but a different manifold?
Even a weirder setup... you know wether or not this wil work on only one of two Audi V8 heads?
If you cut the flange off and weld on a 16V flange it will work.
I am thinking of going a different direction with this car now, I have an awesome running low mile under 100K 2.0 aba with dual delortoro carbs, I am selling this pretty much as a complete swap, all you will need is accessories... I am sure some of you might have seen my car at a show or two. Motor is only been run for 2 seasons, pretty much only been driven around town a little on nice days and to h2o and mk1 madness.. This motor also is pretty bad ass. It sounds amazing! I don't even have a radio in my rabbit and I don't need one because I never get tired of hearing the carbs roar. It is also pretty fast in a rabbit, I am sure a mk2 would be no different, smoked my buddies stock 1.8t audi.
Complete longblock: head/block with brand new oilpan and mostly any gasket I could replace.
Very freshly rebuilt delotoro dual 44 carbs
assortment of jets, and misc parts
Rowand intake manifold w/isolators
Summit fuel pressure regulator w/gauge
Black accell spark plug wires
Complete knock box ignition
Techtonics aba distributor adapter ring
Carter 4070 hflp fuel pump practically brand new
Inline fuel filter
Powdercoated SCAT valve cover
mk4 aeg tubular exhaust manifold
and stock aba manifold with custom modified down pipe to work in a rabbit
New timing belt,plugs, distributor cap and rotor
Throttle cable and bracketry, as well as a choke cable and slick bracket to mount it to your rabbit steering column[was from a diesel rabbit for some sort of choke thing]
There is probably more included I cant think of because I am just rattling off this list by memory.
Pretty much everything pictured here except I am keeping the abf serpentine setup, the oil cooler and transmission...
I am thinking 1600.00 is a fair price considering everything is just about brand new, and I spent 1000.00 on the rebuilt carbs and having them tuned for this motor...
Pretty much all you will need to do is add your accessories and the fire it up.
megasquirt 1 v2.2 complete setup for an 8valve or 16valve engine forsale...i bought this for a previous car...am holding this for a future project currently, but i just bought a house and priorities are priorities...
ms1 v2.2 fuel and spark, gone over by VCG/spitfireEFI
diy autotune relay box (new)
diy autotune jimstim (new)
innovate lc1 w/ gauge (new)
diy autotune relay cable from ms box to relay board (new)
diy autotune harness cable (new, you need to fabricate your own harness)
GM coolant temp sensor (new)
GM open element air temp sensor (new)
obd2 mk3 aba engine wiring harness (was going to hack this up to use the connectors)
8valve digi2 fuel rail w/ stock injectors and
BBM 16valve fuel rail for stock intake manifold w/ an fittings w/ fpr (new)
g60 injector bungs to replace the cis bungs (new)
16valve intake manifold gasket and throttle body gaskets (new)
passat automatic trans throttle body w/ tps
usb cable for ms box (new)
mk4 power distribution block
bosch F6DSR silber spark plugs (new)
and i'll include a DIY autotune license plate surround too...
mostly everything was bought new from diy autotune...would like to recoup some of the money spent, but my loss is your gain...this is pretty much a turnkey setup that all you have to do is finish where i started...
looking for $900...(i am NOT splitting up this setup)
Modified by ratdub at 6:50 PM 2-5-2010
up for sale is a set of jenvey 45mm ITB's, Ive had them for a while and was going to bolt them onto my 16v but decided I want to go turbo so I'm going to start saving now. Comes with horns and itg filters (need oil) the itbs are already tapped for vaccum and IAT, and a TPS. the only thing it will need is a set screw or a billet piece made for the throttle linkage(easy fix). Im hoping to get $1200 shipped but Im open to offers [IMG]http://**********************/smile/emthup.gif[/IMG]
Quote, originally posted by Issam Abed » If you cut the flange off and weld on a 16V flange it will work.
Too bad, would've been the perfect set if it would've been plug and play... and if I had the cash right now.
Thanks for the info anyways.
DHLA Dell'Orto 40's up for sale. Completely disasembled, cleaned and ready for reassemble. Sell Cheap $150 to the first who IM'S Me. Also loads of Dell parts, Air Horns(NEW), Idle and Main Jets(NEW) Also, RARE Factory Dell'Orto Air Cleaner assemblies,Chemically cleaned and Powder coated silver, two sets of new K&N air cleaners as well. will sell everything CHEAP, wan't It all gone. Make me a price for the whole lot as well. IM me , Chris.
Beware the Arizona D-Bags, they know too much!!!!!! ... and Corvettes are over hyped American Junk, just so you know.
[IMG]http://**********************/smile/emthup.gif[/IMG] [IMG]http://**********************/smile/emthup.gif[/IMG] any one have a carb assembly for sale, motorcycle/car. perferably anything with a 40MM+ bore.
i'm contemplating selling the engine out of the scirocco.
high compression RV 1.8 block - rebuilt with new bearings, rings, bolts
solid lifter big valve JH 8v head, port & polished
autotech high rpm valvetrain - valve springs
autotech 286 cam, autotech adjustable gear
dual dellorto 40mm carbs - tuned perfectly - fully rebuilt less than 2k ago
eurosport header - tri-Y
eurosport plug wires
engine has a little over 8k miles. most of these miles are highway - the car has been from georgia to indiana and back several times. it's that reliable. however, it has also done several track days at road atlanta, but never reved above 7500rpm. oil changed every 2k with mobil 1 15w50 synthetic and vw filter. engine is spotless inside. no smoke or oil consumption.
the engine is still in the car. come drive it, hear it, look at it. located in cumming or dahlonega - ATL GA area. will get pulled when i have a deposit on it.
i'm asking $800 as is with all listed. or, we can work something out if you have a low mileage 16v laying around.
I have for sale a complete carb swap of my running 16v. ive already tuned these to match a 1.8 16v with cams and exhaust. im selling all this to fund my 1.8t swap
$900 Shipped OBO
-Dellorto DHLA 40 with Manifold,
-most of a rebuild kit for them
-Extra jets and parts
-duel cable throttle linkage and pedal
-MSD 6a box
-MSD 8990 timing computer
-OEM ignition computer (used as signal booster for timing computer)
my harness also comes with but you may want to clean it up. i can also provide wire diagram if you need.
-Carter 4070 fuel pump, i didn't use or need a regulator for this setup
-i also have a vacuum manifold from Vibrant that is included
The bad, the choke levers on one of the carbs have been broken the whole time ive used them, i didnt need them much so i never bothered to fix it.
im working on getting pics soon. There are some pics of the parts in my old build thread in my SIG
thanks for the views!
Other 16v parts for sale:
auto tech sport cams $200 shipped OBO
polished valve cover $40 shipped OBO
pacesetter 4-1 header $50 shipped OBO
Modified by vee_dubb_gti at 9:47 AM 2-22-2010
..... ,___/ /___l ___\\_____
.......\__( o )_______( o )__/
MS V3 modified for stock VR6 coilpack, tach output
10' harness pigtail
Innovate LC1 Wideband
Will also include the harness and all sensors I wired up for free.
Unit has never been used, selling as new. Over 800 US paid for, will sacrifice for 400 CDN. Price is firm, please email firstname.lastname@example.org or text 905 931 2005 for details. Will drive to meet up at a half way point or deliver if within 50km of st catharines.
Do not send me IM's I do not log onto the tex regularly, email or text is the best bet.
APR B5.5 PASSAT
Certified VW Tech