I am interested, please email firstname.lastname@example.org
as the tital says i have a pair of solex carbs and a dibilas mani fold for sale i had them installed on a 9A engine to find that the lower end was wrecked so im now selling the carbs to clear space
800 obo shipped
pm if intrested
"...we do recommend these for race applications, or those who are just a little off in the head."
I was going to hoard these but i sold all of my mk1's
600 shipped US lower 48 and Canada
new gaskets all cleaned up ready to go. have the cross bar but not the rest of the linkage. other then what you see in photo's.
Mikuni ph44's not sure on the jet sizes but the chokes are 34mm. I never had a chance to run them.
USED great condition EMS 8860 ECU with harness for obd2 mk3 jetta/gti VR6.
Removed from a stock 2.8 Vr6 so the basemap is tuned for that.
Includes factory harness so its plug and play
The only thing you need is a GM coil pack instead of the BS oem coilpack
Includes OEM crank pulley with magnets for crank trigger
PM me for pix
Last edited by vdubfiend; 03-28-2012 at 12:57 AM.
I've got two fresh Dellorto DHLA 40s up for grabs. They were professionally rebuilt and synched.
30mm venturis,135 main jets,57 idle jets,180 air correctors,7772.11 emulsion tubes,38 pump jets,185 idle air bleed jets
These will come with a new Rowland xflow (aba) manifold. New Misab gaskets, new airhorns, and new dial type adjustable fuel pressure regulator.
550 shipped OBO
Last edited by ecksjay; 08-18-2012 at 09:56 AM.
Complete bolt on ready to go carb/ignition setup for 1.8l/2.0l 16v engines. WILL NOT part out the setup so please don't ask. Everything was purchased new or rebuilt and has less then 5k.
Dual DCOE 45 weber carburetors.
TWM DCOE intake manifold.
Professionally rebuilt and road tested last summer buy Speciality Carburetors in Etobicoke
Weber Carburetor Jetting for 2l 16v
Chrome velocity stacks.
Modified coolant flange (allows manifold clearance).
Carter p4070 low pressure high volume fuel pump.
Holly fuel pressure regulator with gauge and filter.
Choke and throttle cables
Carburetor synchronization tool
2 sets of extra tuning jets
Braided stainless connecting fuel lines
MSD pn 8981 programable timing computer.
MSD 6al spark amplifier. (with Ballast resistor and rev limiting chips)
MSD manual timing controller unit with control knob.
MSD blaster 2 coil.
$1500 plus shipping
EM4-4E ECU v11 3bar
MSD adjustable ignition system and harness
New RMR trigger bracket
New 3bar map sensor
Resistor pack for low impedance injectors
#30 drill bits
I have the complete set up for sell here the rack of R1 carbs, adapter, fpr, and carter fuel pump. Ill let it all go for 500. The carbs will come with a set of 2.00 main jets and 1.75 mains. Heres a pic of the set up on my rocco. Im going to go a different route with the project for big power and great fuel economy. Big turbo tdi swap for me.... heres some pics now.
Heres the carb adapter:
And the complete set up on the car.
Sold the adapter still have the carbs extra rack for parts pump ect.
Last edited by MKIGTITDI; 05-07-2012 at 12:34 PM.
Rocco's getting a TDI!!!
I'm selling a new in box Megajolt ignition for TPS. Comes with 2 EDIS 4 modules (one is new in box), coil, trigger wheel, crank sensor, and all pigtails needed for installation. SOLD
I also still have 2 fresh Dellortos professionally built, and 2 new 8v carb intakes for sale. One intake is a Rowland xflow, the other Mikuni counterflow. Need cash for 16v build.
Last edited by ecksjay; 04-23-2012 at 02:48 AM.