For Sale- Wanted To Buy Thread

[rabbot16v]

FS: Innovate LC1 Wideband $150.00 Shipped

SOLD

[rabbot16v]

FS: Genesis 315cc/min - High Impedance (16v & 1.8T)

Used for about 3 years, maybe 10k miles on them.
Great for 16v with standalone.
Factory-correct dual spray cones, fast response, atomizes at injector nozzle and further upon impact with intake valves. Fuel rail spacers not required for 16v or AEB/AGU 1.8T. Other 1.8T engine codes require spacer kit

Looking for $150.00 + shipping



Note: 2 of them look different, but they are all the same injector. When I bought them from USRT, they only had 2 of the old style and 2 newer style in stock.
Never had an issue with them

[black92gl]

I am interested, please email dany@rochester.rr.com

[black92gl]

Do you still have this dizzy for sale? Has it been tested good? oil seals good?

I am Paypal ready.

[vw_monger]

as the tital says i have a pair of solex carbs and a dibilas mani fold for sale i had them installed on a 9A engine to find that the lower end was wrecked so im now selling the carbs to clear space

800 obo shipped

pm if intrested

[78srx440]

I'm looking for an 034 crank trigger kit, or something similar. Please contact me if you have anything. Thanks!

[secondgen]

Still have it. Lowered Price.

What you see, is what you get. Bought this to have options when I went ITB. No longer need it, unused by me, but in used condition. I was told this was made by Drake, but I believe this is untrue, so the price is lower than what I paid for it.

$150 Shipped to the lower 48

[impulse byer]

I was going to hoard these but i sold all of my mk1's

600 shipped US lower 48 and Canada

new gaskets all cleaned up ready to go. have the cross bar but not the rest of the linkage. other then what you see in photo's.

Mikuni ph44's not sure on the jet sizes but the chokes are 34mm. I never had a chance to run them.

[vdubfiend]

USED great condition EMS 8860 ECU with harness for obd2 mk3 jetta/gti VR6.

Removed from a stock 2.8 Vr6 so the basemap is tuned for that.

Includes factory harness so its plug and play

The only thing you need is a GM coil pack instead of the BS oem coilpack

Includes OEM crank pulley with magnets for crank trigger

$1100 OBO

PM me for pix

[ecksjay]

I've got two fresh Dellorto DHLA 40s up for grabs. They were professionally rebuilt and synched.

Specs:

30mm venturis,135 main jets,57 idle jets,180 air correctors,7772.11 emulsion tubes,38 pump jets,185 idle air bleed jets

These will come with a new Rowland xflow (aba) manifold. New Misab gaskets, new airhorns, and new dial type adjustable fuel pressure regulator.

550 shipped OBO

SOLD

[Tougemachine]

Still have it. Lowered Price.

8v or 16v

[stick90]

Dellorto DHLA 40's with 8v mani.
They have been sitting for a few years so might be a good idea to put kits in them.
Came of a 1.8
500 shipped obo

[mpr3ssiv]

WTB: R1 Carbs

for my 16v, email me with pictures and price!



andresvillanu20@gmail.com

[marc124444]

Update Vibrant good for ITB

4 NEW available @ 10$ each SHIPPED

[eurotrashrabbit]

New $125 plus shipping in the USA. Throttle bodies or carbs Rowland manifold

[cubanvr6jetta]

I need
Manifolds for r1 carbs 16v and 8v aba pls help cash on hand need asap 2018786641 txt me pls

Sent from my SCH-R910 using Tapatalk

[ALLGORIMSHOW]

SOLD



Complete bolt on ready to go carb/ignition setup for 1.8l/2.0l 16v engines. WILL NOT part out the setup so please don't ask. Everything was purchased new or rebuilt and has less then 5k.

Fuel/Intake System:
Dual DCOE 45 weber carburetors.
TWM DCOE intake manifold.
Professionally rebuilt and road tested last summer buy Speciality Carburetors in Etobicoke
Weber Carburetor Jetting for 2l 16v
Chrome velocity stacks.
Modified coolant flange (allows manifold clearance).
Carter p4070 low pressure high volume fuel pump.
Holly fuel pressure regulator with gauge and filter.
Choke and throttle cables
Carburetor synchronization tool
2 sets of extra tuning jets
Braided stainless connecting fuel lines

Ignition:
MSD pn 8981 programable timing computer.
MSD 6al spark amplifier. (with Ballast resistor and rev limiting chips)
MSD manual timing controller unit with control knob.
MSD blaster 2 coil.

$1500 plus shipping

[ncbrock]

anyone have any weber pump jets? looking for ~45-60

[ZWaters10]

Still have this setup?

I've got two fresh Dellorto DHLA 40s up for grabs. They were professionally rebuilt and synched.

Specs:

30mm venturis,135 main jets,57 idle jets,180 air correctors,7772.11 emulsion tubes,38 pump jets,185 idle air bleed jets

These will come with either a Rowland xflow manifold or a counterflow manifold. Both are new. Counterflow manifold comes with linkage. The intake that doesnt sell with the carbs will also be for sale.

600 shipped OBO.

[ecksjay]

Still have this setup?

I still have all of it. The guy that wanted it never sent the money.
I'll include the air horns I just bought that aren't pictured and a new fuel pressure regulator.

[ALLGORIMSHOW]

$800
EM4-4E ECU v11 3bar
Main Harness
Injector Harness
Controller/Cable
Crank sensor
Mixture box
MSD adjustable ignition system and harness
Blaster coil
New RMR trigger bracket
New 3bar map sensor
Resistor pack for low impedance injectors
#30 drill bits

[ca180]

WTB set of velocity stacks/trumpets/whatever you want to call them.....

2-3" please so they fit inside my K&N Filters, but longer is fine.

Hoping for a good deal.... i do have a US shipping address.

LMK, thanks

[MKIGTITDI]

I have the complete set up for sell here the rack of R1 carbs, adapter, fpr, and carter fuel pump. Ill let it all go for 500. The carbs will come with a set of 2.00 main jets and 1.75 mains. Heres a pic of the set up on my rocco. Im going to go a different route with the project for big power and great fuel economy. Big turbo tdi swap for me.... heres some pics now.
Heres the carb adapter:

And the complete set up on the car.


Sold the adapter still have the carbs extra rack for parts pump ect.

[psychobandito]

Urgently looking for an Auto 16v throttle body.

paypal ready.

[oldschool eighty8]

I have four 2" couplers and four t-bolt clamps from
034 motorsports. Have not been used yet, they are too big for the r1 carbs. May fit itb's or other carb setups?
I'd like to get 40 shipped for all of them.

[ecksjay]

I'm selling a new in box Megajolt ignition for TPS. Comes with 2 EDIS 4 modules (one is new in box), coil, trigger wheel, crank sensor, and all pigtails needed for installation. SOLD

I also still have 2 fresh Dellortos professionally built, and 2 new 8v carb intakes for sale. One intake is a Rowland xflow, the other Mikuni counterflow. Need cash for 16v build.

[hantonyc]

WTB saab vacuum advance distributor , must be shipped by USPS to quebec, canada , in private msg thanks !

[rysskii3]

installed but never used:

[oldschool eighty8]

aem uego wideband + megasquirt 1 v2.2 comes with all sensors, distributor, ICM, coil and serial to usb adapter

320 shipped.

YZF R1 itbs 50mm inlet


100 shipped.

pm me if interested.

Willing to sell the wideband separate?

[bonesaw]

AEB Coils and connectors. $50/set + shipping


2.9 Throttle Body $150 shipped

[hantonyc]

in need of my saab dizzy FAST , willing to pay more then what its worth..

[Tougemachine]

in need of my saab dizzy FAST , willing to pay more then what its worth..

(408) 834-0951
Hell hook yu up. Tell him Nathan referred you. And you want the same distributor

[hantonyc]

i live in canada, cant really call in the US , can u hook me up ?

[Tougemachine]

P.m. Me

[bucketoval]

looking for a manifold for a 8v to use a single idf carb. i have the carb need the manifold it is going on a mk1 with a 1.7