Sale: New 16V Distributors, Cams, Ignition Wires, Gasket Sets, Pistons, Rods

[FourSeasonTuning.com]

We would recommend you use modeling clay to see if you have any contact.
We don't know what your head or block tolerances are, either may have been decked in the past.
As for the pistons, we recommend the 83mm and have your block bored. This would allow for the proper wall clearance for expansion and also proper oil control.

The UK is covered by Paypal sellers protection, so we can accept any major credit card via Paypal.
Before you purchase please ask for a freight quote.
Due to a recent change with Royal Mail and the USPS, all international orders over $100 will be shipped Express Mail. This is done because they allow for higher insurance rates to cover loss.

www.fourseasontuning.com

[Bazmcc]

We would recommend you use modeling clay to see if you have any contact.
We don't know what your head or block tolerances are, either may have been decked in the past.
As for the pistons, we recommend the 83mm and have your block bored. This would allow for the proper wall clearance for expansion and also proper oil control.

The UK is covered by Paypal sellers protection, so we can accept any major credit card via Paypal.
Before you purchase please ask for a freight quote.
Due to a recent change with Royal Mail and the USPS, all international orders over $100 will be shipped Express Mail. This is done because they allow for higher insurance rates to cover loss.

www.fourseasontuning.com

I understand but ideally that test would be done with the new pistons. The head is untouched as far as I can see. See below for block tolerances without head gasket.

[FourSeasonTuning.com]

IM sent.

www.fourseasontuning.com

[Bazmcc]

OK I'm going to go for a set of the K9031D050 83mm Wossner pistons. The high compression ones. You can let me know if these are definitely correct. The parts numbers are easily mixed up. Can you confirm that these include rings, pins, and clips?

Let me know about shipment for these (I think $75 was mentioned) and the total and how the paypal payment can be done and I can sort that out.

My friend is going to have a look at your site and let me know if he needs anything for his VR6 as well. If not, it'll just be the pistons.

[2008cc]

need a price on autotech cams, valve springs and lifters.

[FourSeasonTuning.com]

IM replied, ordered shipped.

[2008cc]

Easy transaction.

[Bazmcc]

Top quality products, service and prices.

[eme411]

I have a 87 Scirocco 1.8 16v with digi1 fuel set up, will this wideband work with digi1 and how does it work when i already have a O2 sensor.

Innovate Motorsports Wideband Blue Gauge Part Number: 3795

[FourSeasonTuning.com]

The 02 sensor in the innovate kit would not replace your current narrow band 02. It comes with a bung that should be welded in pre-cat. This will only give you a readout, it will not adjust your current setup at all.

These are more commonly used in boosted cars to keep an eye on the AFR.

[Roger@Silvern16vT]

Do you send to Norway ?

I'm interested in:
-16V Distributor for my 1,8 16V KR engine- with cap and rotor

And maybe if you can give me good price on this things:
-8MM Ignition Wire Set RED Fits 1.8 16V
-1.8- 2.0 Lightweight lifter set

[FourSeasonTuning.com]

IM sent with information.

[ArsenicPants]

I finally went out to my US mailbox to pick up my light weight lifters
the shipping itself was very fast, I just had to wait a while to pick them up
great product, well packaged, fast, great stuff guys

although the packing grease from the lifters had leaked out and caused the paper in the box to become see through, hahaha

[azki69]

hello do you sell intake valves for a 1.8 16v engine i would need 8 of them thanks

[FourSeasonTuning.com]

$18 each made in Italy.

[phrankentruk]

How much for cast 83 or 83.5mm pistons/rings?

[FourSeasonTuning.com]

Contact us at the shop to discuss your needs.

Our number is in the sig below.

[npvk_x]

Hey.. my order arrived today.. Thanks!

you will hear form me again.

[baggedgti]

I need a complete engine gasket set for a 9a 2.0 16v pm me please

Sent from my DROID RAZR using Tapatalk 2

[shysty]

up