I'll add my .02 I removed the passenger side axle and CV joint so I could remove the broken vibration damper.
#1
stolen from the MkII forum.today i installed my factory mudflaps...
two days ago i had my ass handed to me by an Acura RSX
![]()
#2
I'll add my .02 I removed the passenger side axle and CV joint so I could remove the broken vibration damper.
#3
Pretty much nothing, as I am a few thousand
miles away from it now![]()
FS: AAA VR6 thermostat cover, B4 lower C-pillar plastic trim
VW DIYs and guides, color codes, DTC/P-codes
#4
looked over all of my vaccum hoses cause i have been hitting limp mode the past few days....![]()
Originally Posted by upoo2
Originally Posted by dano17
#5
washed her up real nice, and today adding some battery post shims to my sh!tty wal-mart battery.
#6
Quote, originally posted by arawak420 » washed her up real nice, and today adding some battery post shims to my sh!tty wal-mart battery. if that doesnt do it for you, aluminium foil will do the trick.
I p;ssed on my car today.![]()
#7
i kicked mine several time after i just got done resolving the running issues and the heaterbox issue. only to find out that the drivers front claliper siezed... i dented the bottom of my trunk...if anyone wants a GLX passat with a slew of new parts it can be yours for 2700 bucks
![]()
#9
Changed fan thermal-switch to a low temperature one. ordered bunches parts from http://www.autohausaz.com/ for weekend DIY job,espacially motor mounts.
#10
washed mine real good today, tomorrow in detailing the interior, i have a show to attend on sunday![]()
#11
installed P-chip(thanks Brad!), replaced cabin filter, and a quick wipe-down to shine it up![]()
#12
installed a vacuume block and boost controller. Washed it too. Got gas also, it eats gas![]()
#13
Quote, originally posted by ACschnitzer23 » installed a vacuume block and boost controller. Washed it too. Got gas also, it eats gas ![]()
i bet it eats Mustangs too
![]()
#14
Quote, originally posted by projects » ordered bunches parts from http://www.autohausaz.com/ Good choice
![]()
FS: AAA VR6 thermostat cover, B4 lower C-pillar plastic trim
VW DIYs and guides, color codes, DTC/P-codes
#15
got mine running with MSD 6a, MSD 8980 and a hot Bosch coil...so SCHWEEET! My daughters civic can rest now.![]()
#16
finished up the details for the most part, all i have left is the motor....
#17
Ordered Low Temp Thermostat kit, and new front left ABS sensor, and adjusted my coils
16" Monte Carlos for sale! http://forums.vwvortex.com/showthrea...-Tristate-Area
#19
Received parts from http://www.autohausaz.com/
So I'll do some jobs:
1.engine/tranny mounts.
2.tranny filter and oil change.
3.fan drive belt.
4.install transmission cooler
5. install a heat shield for abs brake system.
#20
I blew out one of my front 205/40/ZR17. So until my new tires come in for the front I am going JDM style running the stockers up front with some nice 17's in the back. I get a lot of thumbs up from the honda crowd![]()
#21
drove to minni last week, today i cruised around with the girl, parked it in the garage![]()
#22
woke up in the back of the wagon this morning
NEK....PISS OFF
R.I.P ALEXI
#23
Quote, originally posted by ACschnitzer23 » installed a vacuume block and boost controller. Washed it too. Got gas also, it eats gas ![]()
VR6T and no pictures? How cruel...POST UP!
I finally got my CEL fixed and I smoked a Civic
![]()
Daily Driven
Whatta you lookin at butthead
#24
I'd just stare at it every time I go outside to the driveway. Its been parked since April needing some suspension work.![]()
![]()
![]()
#25
Quote, originally posted by DubPassatVR6 » VR6T and no pictures? How cruel...POST UP!
FS: AAA VR6 thermostat cover, B4 lower C-pillar plastic trim
VW DIYs and guides, color codes, DTC/P-codes
#26
ehhh...very nice!!
Daily Driven
Whatta you lookin at butthead
#27
worked on installing the new air intake boot and started sanding the grill to put a wrinkle texture look on it.
#28
today i finished for the mostpart cleaning my engine bay while we were slow at work. im gonna pull some stuff out of the wat to get it more detailed my next weekend off
#29
I pulled it out of the garage today so I could do an oil change on my S6![]()
#30
well i thought about sitting in it but it smells like gas coz stupid me forgot to take the relay out and decided to roll down the windows ..reason is coz i undone the fuel lines from the tank coz the fuel pump needs work and didnt think of taking out the relay so when i turned it on the pump in the tank started and now my trunk is gas soaked ...bummer![]()
![]()
![]()
![]()
![]()
![]()
but oh well you live you learn...
![]()
#31
Filled her up with gas to the tune of $3.00/gallon. Friggin premium!![]()
Daily Driven
Whatta you lookin at butthead
#32
the price you pay for premium, us canadians get regular... 87 oct , and then pay about 4 more cents![]()
#33
deep clean of the paint (polish & wax) and change my replica's RS4 for a Borbet Rex8, both 17
![]()
#34
pulled all my damaged panals off only to find a bent frame rail......so yeah thinking about parting her out now
#35
Quote, originally posted by DubPassatVR6 » VR6T and no pictures? How cruel...POST UP!
haha how rude of me!
![]()
Here are some recent pictures.Today I finished the timing belt change on my 03 Passat 1.8Turd
Today also I put in a new fog light where my glass fell out and broke. Thanks Triple Seis!My engine is really cluttered, gonna clean it up some. Its pretty much all custom fabricated with the exception of C2 MAF and chip and Kinetic manifold.
Modified by ACschnitzer23 at 4:52 PM 7-31-2007