Ask a VW Parts Guy....Passat Edition

[JohnEcanuck]

I need a grab rail for my 07 Passat wagon, part number 1T0-827-547-L.

Any help? Local stealership is charging $160. Obviously looking to find one for less.

[rookie]

I have a question -
I have a 2010 Passat with the 6sp DSG transmission

I was reading about the DSG transmissions, and it looks like they came in two flavors - the 09G and 09M

From what I can find, the 09G is what my Passat has, curiously, the specs say that the 09G is rated to only 184 lbs-Ft. of torque whereas my car comes stock with 207

Is this wrong, right or am I way off. I checked my code sheet and don't see anything stating a 09G or 09M. I'm guessing it's the D6F code. If so, what are the specs of that transmission.



Thanks

[Adam@CheckeredFlagVW]

I have a question -
I have a 2010 Passat with the 6sp DSG transmission

I was reading about the DSG transmissions, and it looks like they came in two flavors - the 09G and 09M

From what I can find, the 09G is what my Passat has, curiously, the specs say that the 09G is rated to only 184 lbs-Ft. of torque whereas my car comes stock with 207

Is this wrong, right or am I way off. I checked my code sheet and don't see anything stating a 09G or 09M. I'm guessing it's the D6F code. If so, what are the specs of that transmission.

Thanks

You actually have an 02E transmission....I dont have anything in my parts catalog to say the specs. Ill look around and see what I can find

[rookie]

Okay -02E tells me alot
Max torque of 350 NM (258 ft-lbs.)

Unbelievably complete pdf at:
http://www.evosoft.dk/diagrams/DSG_02E.pdf

[Adam@CheckeredFlagVW]

Okay -02E tells me alot
Max torque of 350 NM (258 ft-lbs.)

Unbelievably complete pdf at:
http://www.evosoft.dk/diagrams/DSG_02E.pdf

good stuff

[rookie]

I know this would be a pain, but is there any way to decode that options code sheet?

Damn, which one even says what color paint I have?

Also - trying to figure which fuse is my fuel flap and what else is on that circuit.

I keep getting a "Short to ground" code when I push my fuel flap button.
I bought a new actuator, but it didn't help.

It must be something else on that circuit as if it was a true "short" - it would be blowing the fuse. Instead it just doesn't work and throws a code. I've made a couple mods and have tried disconnecting them all, but nothing seems make a difference. The switch is fine and I've even traced the wires thru the transmission tunnel and haven't found a thing.

Thanks again - you are a wealth of knowledge and a great contributor to the Tex

[coderedcomputing]

Greetings Parts guys!

I have a request, I may need to buy a few body panels...

2008 Passat 2.0T TSI

Right & Left Sides for these:

Turn Signal 'housing' the body/fiberglass/whatever that the turn signal sits inside of...

The body piece that sits next to the turn signal, a strange bump out that on my model does not look like it is a formed part of the bumper (heard that later models have this fused with the bumper)...

Appreciate the help!

[mtnryder]

Hows it going parts guys,

I broke the oil filter housing on my 08 3.6 4motion. Do you know the part # for this?

thanks!

[nodashi]

looking for a aluminum dash trim where can i get one of those?

[Adam@CheckeredFlagVW]

Hows it going parts guys,

I broke the oil filter housing on my 08 3.6 4motion. Do you know the part # for this?

thanks!

071-115-433

[JohnEcanuck]

I need a grab rail for my 07 Passat wagon, part number 1T0-827-547-L.

Any help? Local stealership is charging $160. Obviously looking to find one for less.

Anyone?

[Adam@CheckeredFlagVW]

Anyone?

The part number is no good....shoot me your vin Ill get you a price on it

[Cranford803]

looking for a aluminum dash trim where can i get one of those?

You should consider wrapping with 3M vinyl.

[VWPalmer]

Any chance I could get a part number for a non tow hook hole lower rear valance (the black texture bit at the bottom of the back bumper) and the the part number for the same part on an r line Passat.

Thanks

[coderedcomputing]

Greetings Parts guys!

I have a request, I may need to buy a few body panels...

2008 Passat 2.0T TSI

Right & Left Sides for these:

Turn Signal 'housing' the body/fiberglass/whatever that the turn signal sits inside of...

The body piece that sits next to the turn signal, a strange bump out that on my model does not look like it is a formed part of the bumper (heard that later models have this fused with the bumper)...

Appreciate the help!

Found a bit more info if this helps:

http://www.jimellisvwparts.com/showA...front%20bumper

On the diagram listed above, I'm looking for part #37 and #40 but can't find much info about them... any ideas?

Thanks!

[Juniorfeel]

Can someone give me a link to somewhere I can get the updated fuel cap from? Or even a part number would be great. I tried searching and even ECS didn't have what I was told to be the revised cap...the one ending in "G." Thanks

[Born²VW]

I have an 07 4mo

I am installing Neuspeed sport springs soon. Maybe tomorrow.
I have the replacement bolts install kit.

Anything else critical to replace when doing this install?
I have read about a bushing or barring that might need to be replaced.

Can you give me part numbers and names please?
And classify it's importance of being replaced? (scale 1-10)

Thank you.

[Adam@CheckeredFlagVW]

Can someone give me a link to somewhere I can get the updated fuel cap from? Or even a part number would be great. I tried searching and even ECS didn't have what I was told to be the revised cap...the one ending in "G." Thanks

It is actually revised further to 3C0-201-550-N, I have one in stock, $16.50 plus shipping. Give me a call if you would like to order

[Adam@CheckeredFlagVW]

I have an 07 4mo

I am installing Neuspeed sport springs soon. Maybe tomorrow.
I have the replacement bolts install kit.

Anything else critical to replace when doing this install?
I have read about a bushing or barring that might need to be replaced.

Can you give me part numbers and names please?
And classify it's importance of being replaced? (scale 1-10)

Thank you.

I would do the front strut mounts and bearings while you have them off:

1K0-412-331-B x2 (Strut Mounts)
6N0-412-249-C x2 (Bearings)

As long as you have the bolt kits I believe thats all you will need

[Born²VW]

Thank you.

[GR8FL DAD]

3c0-854-939-a-9b9 cover - $32.44
3c0-854-940-a-9b9 cover - $32.44
3c0-854-949-a-9b9 cover - $28.31
3c0-854-950-a-9b9 cover - $28.31

I do have to order these. just give me a call if you would like to order

I may be interested in purchasing these pieces as well. I just painted and installed votex sides and would like to color match the lower doors.

Do you know how they attach? I have read some different threads talking about having to modify the tabs on the front door pieces to make them fit and that you have to then put them on with adhesive tape. I have a late 08 TSI Passat if that makes any difference.

[vw_nc_dude]

I have a question:

I ordered the below OEM 4-spoke leather steering wheel for my 2008 Passat. When installing this in my car, I will not use the multifunction buttons on the left and right side of the wheel. Are there any plastic inserts for these spots if I want to take these buttons out?

[MDAce15]

Can you tell me the part number for the oil dipstick on an 07 3.6 Passat? Thanks. I think I may have the wrong one...

[N715DP]

Can someone confirm if the following part number (steering wheel control module) supports MFSW?

3C0-953-549-N

It's not listed on the Ross-Tech site: http://wiki.ross-tech.com/wiki/index...er_3C0-953-549

[Adam@CheckeredFlagVW]

can you tell me the part number for the oil dipstick on an 07 3.6 passat? Thanks. I think i may have the wrong one...

03h-115-607-c

[MDAce15]

03h-115-607-c

Thanks a lot! Much appreciated.

[coderedcomputing]

Can any of you parts guys confirm for me what part these are:

ZSB 3C5.945.095 C
ZSB 3C5.945.096 C

Trying to see if these are standard USD or if they are the EU ones with amber turn LEDs.

Gracias!

[iowarabbit]

kind of a mkv/b6 mash-up question...
i'm planning on driving my parking brake via linear actuator and want to hack the passat center console into my rabbit. it appears that the climate controls roughly line up and i can feel the passat mount holes beneath the carpet along the side of the center hump. are there different passat-specific braces beneath the ashtray area to help support the console? part #'s or pics would be very helpful.

EDIT: looks like the part #s i need are the left/right/center retaining brackets from the passat front console.

[BPhillipsGLI]

Does anyone have a part number for the OEM Chrome roof rails that come on the 3.6 4mo VW Passat wagon, as well as a price? Thanks.

[chris.betsch]

Do the Side mirrors on a 08 Passat snap into the mirror housing or are they stuck with an adhesive backing?

[coderedcomputing]

Do the Side mirrors on a 08 Passat snap into the mirror housing or are they stuck with an adhesive backing?

They snap in, check this link from ECS it has a video on there for the replacement of the mirrors:

http://www.ecstuning.com/Volkswagen-..._BIS_ES252586/

[jachong]

Anyone has a Votex front lip on stock? If so, please msg me.

Thank you very much!

~ja

[CEO]

I'm going to change the Haldex and differentials fluids in my 2008 Passat, 3.6L, 4motion. I need drain and fill plugs for both front and rear diffs and the Haldex. I also need the Haldex oil filter. I'm assuming that the plugs come with gaskets/seals. I do not have part numbers. I'd like to get these ordered as soon as possible. Can anyone help me out? Thanks.

[miki2006]

Hello to all part guys !!! I just need a little help trying to find out which is the right part number of a multifunction airbag harness with double stage bag, mycar is a b6 2.0t 2006. The #'s are:
1k0 971 584 or 1C0 971 584, the one 1c0971585B is for single stage airbag. I haven't buy yet the control module which is the 3C0-953-549-AH* so can anyone give a quote of harness and module + shipping to 11746.
Thanks

[MK4Laxer]

Hey, do u know if i am able to swap out my frame with another b6 passat frame? also do you know if the engine bay frame is removable by itself? i was informed that it is a bolt on frame, does that mean if my engine bay frame is bent, i can replace just that part of the frame?