If you guys would like to send me a Micro-CAN cable I'll be happy to test out 3.6 VR BLV.
I plan to buy one soon anyway.
Attached is a document that explains how to set the readiness code in the W12 engine. I have already mapped out both controllers for this engine when I wrote the label files for the W12.
If you want me to test a script and see if it works, send me an email. Click on my user name (to the left) to reveal my email address.
Have been using LAUNCH tool,but we got 09 A4 and several modules cannot be reached (SRS,engine,transmission...),so will call Monday and order VAG-COM.(have older one that I used years back,but that doesn't work on newer VW/audi.Hope the HEX-USB-CAN covers B8 audi.For the money it sounds like great deal.
Quote, originally posted by Rabbid0281 » Hey Santos, managed to relocate my cable, and just picked up an 04 Passat GLS manny. Any new scripts for it or 08 Rabbit S?
Send me an autoscan for both cars and i will check to see what's available.
Quote, originally posted by miltak » .Hope the HEX-USB-CAN covers B8 audi.For the money it sounds like great deal.
VCDS does have the ability to access all modules in the B8 Audi. Please see:
I will get them to you soon as I can. Still have to drive upto Dallas to get the cable from my parents house. I have a baseline scan saved for my Rabbit incase I ever needed a "reset" button.
one more question, would you use the beta VCDS or the full Release version? I've never had any problems using either, but just wondering.
Quote, originally posted by Rabbid0281 » one more question, would you use the beta VCDS or the full Release version? I've never had any problems using either, but just wondering.
I would use the beta for readiness testing. The beta shows the name of script loaded in title bar and under the [Set Readiness] button. It will also let you know if a script is not available.
I tested on my mkvi golf tdi some of the radio options...
I went through the adaption guessing codes...
I did figure out that channel 10
when you change the bit to 1
the radio changes and says on the screen
this will make it so you cant use the controls
only the volume works...
when you turn the car off, the radio stays on, but the screen turns off...
If you know what this means, please post
my computer froze on many of the guessing options... but i keep at it
Santos is on vacation, so I'm not sure about the status of the logs you sent.
It's always best to run the scrips he sends out for each engine, but I don't know when he will reply with a script. So..In general, the 1.8T readiness procedure is pretty simple / standardized. This is a very old post of mine that will work on the 1.8T also. Use the second procedure and substitute the 202 and 228 for the older 071 and 070 evap tests.
Sorry for the CAPS: http://forums.vwvortex.com/showthread.php?2213402
You might want to add 107 at idle to that test sequence.
I have a 2005 Golf TDi, (BEW).
I would love to help you guys out. My EGR is blocked and cycle reduced from the flash-tune. I am also running a 3" straight exhaust (no cat). The O2 sensor is still in place. On the PD TDI it is pre-cat and located in the Downpipe.
Will my car be of any use to you? If so, let me know and I'll follow your instructions and shoot you the e-mail.
I have 2.0 TDI CR and I think I can test file for this engine.
Address 01: Engine (CBD) Labels: 03L-906-022-CBA.clb
Part No SW: 03L 906 022 R HW: 03L 906 022 G
Component: R4 2,0L EDC G200SG 3436
Revision: 13H01--- Serial number: VWX7Z0H93N90Z0
Shop #: WSC 00020 259 80144
No fault code found.
Readiness: 0 0 0 0 0