** GruvenParts.com Has Billet Passat Goodies !!

[GruvenParts.com]

1.8T billet dipstick funnels will be online this week !

www.GruvenParts.com

[GruvenParts.com]

Billet 12V VR6 Drive Belt Pulleys - All 12V VR6

GruvenParts.com offers a complete set of ultra sleek lightweight 12V VR6 power pulleys. These include lightweight billet crank, power steering, water pump, tensioner, and alternator pulleys for your 12V VR6 engine. These pulleys are precision CNC'd from aircraft grade billet aluminum and reduce the rotating mass by a whopping 8.5 lbs! All pulleys with exception of power steering pulley ARE NORMAL DRIVE (NOT UNDER-DRIVE). Our testing has determined that ONLY the power steering pulley should be under-driven (slightly). All other pulleys in the system rotate at the OEM speed. These pulleys will not change the speed of the supercharger and will not void any supercharger warranties.

Buy them as a set and save!

These pulleys replace the following OEM part numbers :

Crank Pulley : 021-105-243 (021105243)
Tensioner Pulley: 021-145-299 (021145299)
Water Pump Pulley: 021-121-031A (021121031A)
Alternator Pulley:
Power Steering Pulley : 021-145-255 (021145255)

[GruvenParts.com]

www.GruvenParts.com

[GruvenParts.com]

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

DOES NOT COME WITH CHEAP THIN WALL TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

Ours are completely tig welded by our licensed commercial jet aircraft repair facility! We were the 1st to build this part and its what started us off! If you have a billet crack pipe in your VR6, chances are it was made by http://www.GruvenParts.com. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! The 12V version replaces OEM p/n 021-121-050C (021121050C) and the 24V version replaces OEM p/n 022-121-050 (022121050).

[GruvenParts.com]

www.GruvenParts.com

[GruvenParts.com]

VR6 Billet Aux Water Pump Bracket – All VR6

This part replaces the useless rubber donut OEM P/N 035-959-209E (035959209E) that does a poor job supporting your PRICEY auxiliary water pump, and related PRICEY hoses. The OEM rubber donut allows the weight of the pump and hoses to sag, causing stress which can lead to pump and hose failure. Our billet version is the way VW should of designed it to begin with and locks the pump and hoses tight! On or off track, this part will secure the aux pump and prevent pump and hose failure.

Replaces OEM P/N 035-959-209E (035959209E) common to the following vehicles -

Corrado - all VR6
Eos - 2007 + 3.2L VR6
Eurovan - All VR6
R32 - 2004
Golf, Jetta, Jetta Wagon - 1993-2007 All VR6
Passat - 1992-2005 - All VR6 and V8
Phaeton - 2004-2007 6L V12
Touareg - 2003 on 3.2L VR6

[GruvenParts.com]

What other parts do you guys want ? Email, PM, or post please

www.GruvenParts.com

[GruvenParts.com]

FYI –

Billet Dipsticks to match our billet funnels are coming. Should be listed on the site this week!

[GruvenParts.com]

Got an 02A Trans ?? Then you better have a look at these upgraded billet shift linkage parts !


02A Billet Stainless Steel Short Shifter Bracket
Replace the weak plastic link in your cable shift mechanism with this one made from Aerospace grade, hardened stainless steel. Reduces side/side shift throw by 35%! This part replaces OEM P/N 1J0-711-256 (1J0711256) common to most 02A cable shift MK3, MK4 Jettas, Golfs, TDI’s, Beetles, Passats, and Corrado VR6.

Replaces OEM P/N 1J0-711-256 (1J0711256)


Stainless FWD/AFT Steel Shift Cable Repair Block

GruvenParts.com is proud to release this solid stainless fwd/aft cable shift repair block for cable shift VW vehicles. This part will quickly replace the weak forward end of the factory fwd/aft shift cable P/N 1H0711265 (1HO-711-265) where it connects to the transmission linkage. There is no need to source an entire shift cable mechanism (which is very hard to find, and also quite pricey) in the event of a broken fwd/aft shift cable. And if your cable is not yet broken, throw 1 of these in the glove box and be prepared for the inevitable!

This repair block repairs the FWD/AFT cable P/N 1H0711265 (1HO-711-265) common to most 02A cable shift MK3, MK4 Jettas, Golfs, TDI’s, Beetles, Passats, and Corrado VR6.


Stainless SIDE/SIDE Steel Shift Cable Repair Block

GruvenParts.com now also has solid stainless side/side cable shift repair blocks for cable shift VW vehicles. Once again, there is no need to source an entire shift cable mechanism (which is very hard to find, and also quite pricey) in the event of a broken shift cable. And if your cable is not yet broken, throw 1 of these in the glove box and be prepared for the inevitable!

Add some indestructible hardware to the factory cable shift mechanism where it needs it most! Buy these parts together and save!!

[GruvenParts.com]

Bump for billet goodness and lots more is on the way !

www.GruvenParts.com

[GruvenParts.com]

MK2 / MK3 Billet Fuel Line Support Brackets

Billet fuel line support brackets (set of 2) to replace the weak plastic clips that are probably long gone on your MK2 and MK3 VR6. Ours are CNC'd from billet aluminum to perfectly match the size and shape of your VR6 fuel lines. Mount directly to the head in place of existing plastic supports and install with supplied aerospace grade stainless fasteners. Dont leave your VR6 fuel lines loose and rubbing against hot engine components! These will take more abuse than you can dish out, guaranteed!!

Can be chrome plated for those seeking even more engine bay bling.

Fits all MK2 and MK3 VR6 - Jetta, GTI, Passat, and Corrado. Includes stainless bracket hardware, re-use existing 10mm nuts to bolt to head. Brackets replace OEM P/N 021-133-827 (021133827) Bracket and P/N 021-133-687A (021133687A) clip.

[GruvenParts.com]

www.gruvenparts.com

[GruvenParts.com]

[GruvenParts.com]

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

DOES NOT COME WITH CHEAP THIN WALL TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

Ours are completely tig welded by our licensed commercial jet aircraft repair facility! We were the 1st to build this part and its what started us off! If you have a billet crack pipe in your VR6, chances are it was made by http://www.GruvenParts.com. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! The 12V version replaces OEM p/n 021-121-050C (021121050C) and the 24V version replaces OEM p/n 022-121-050 (022121050).

[GruvenParts.com]

There is NO TAPPED FITTINGS on this part, and therefore NOTHING to leak. Not needed when you have FAA approved aerospace TIG welding equipment in house.

GruvenParts.com builds bulletproof TIG welded Y Pipes to replace the OEM plastic in your VW coolant system!



Replaces the following OEM P/N :

1H0-122-101E (1H0122101E) – MK3 Golf/Jetta VR6
3A0-122-101E (3A0122101E) – VR6 Passat
1C0-121-438A (1C0121438A) – New Beetle

www.GruvenParts.com

[GruvenParts.com]

GruvenParts.com Die Cut Vinyl Stickers - Free for Orders over $100 !

They're Back In Stock - Bigger and Better !! All Colors Now Available. Dress up your ride with our premium die cut vinyl stickers and enjoy free domestic shipping.

Available in Red, Silver, White and Black.

We ship out a freebie with any order over $100 !

[GruvenParts.com]

www.GruvenParts.com

[GruvenParts.com]

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

MACHINED FROM 6061-T651 ALUMINUM TO EXACTLY MATCH OEM PIPE DIMENSIONS - OURS DOES NOT COME WITH CHEAP THIN WALLED TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

GruvenParts.com was the 1st to build this part and it’s what started us off! We manufacture this pipe EXACTLY to match the OEM part shape so there is NEVER a fitment issue. Be careful when considering other billet pipes which do not match the exact shape of the OEM pipe. The fitment of this part is tricky and the shape MUST BE IDENTICAL to the OEM part to ensure correct alignment between the water pump and thermo housing.

If you have a billet crack pipe in your VR6, chances are it was made by us. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! Our pipe has a modular design which allows you to plug the oil cooler feed line with a ¼ NPT plug if installing an external oil cooler. Ours can also be ordered with a chrome plated drain valve for quick and clean coolant flushes. The pipe can also be ordered with a brilliant chrome finish for those seeking the ultimate engine bay bling!

If you dont want to do this job again, buy the LIFETIME WARRANTED GruvenParts.com billet CrackPipe !

Make sure to see our website for the complete installation DIY

The 12V version replaces OEM p/n 021-121-050C (021121050C) found in 12V VR6 : VW Corrado, Golf, Jetta, Passat, and Eurovan.
The 24V version replaces OEM p/n 022-121-050 (022121050) found in 24V VR6 : VW R32, Golf, Jetta, Eurovan, EOS, Audi : 3.2L V6 TT and A3

[GruvenParts.com]

AAA VR6 Billet Dipsticks

www.GruvenParts.com is proud to release this Billet Dipstick for all AAA VR6 Corrado, Golf, Jetta, and Passat!

The gorgeous dipstick is CNC’d from a chunk of aerospace grade aluminum and contains 2 chemically resistant O-rings for a perfect fit and seal.

Get rid of the ugly plastic dipstick and replace with our billet version!

This part replaces the dipstick on AAA VR6 engines found on Corrado VR6, MK3 Golf, Jetta, and Passat with OEM dipstick p/n 021115607 and OEM tube p/n 021115629E.

[GruvenParts.com]

GruvenParts.com builds bulletproof TIG welded Y Pipes to replace the OEM plastic in your VW coolant system!


Billet Upper Radiator Hose Y Pipes

PLEASE NOTE : This part is professionally TIG welded! There are no junk tapped threads into thin wall aluminum like the lesser versions offered by unscrupulous rip off artists. And its warranted for life!

An absolute MUST HAVE for all MK3 VR6 owners and MK4 New Beetle owners. The upper radiator hose on these models is quite a pricey item from the dealer – usually about $100. The most documented cause of replacement on this hose is due to the plastic Y fitting which connects the 3 short hose pieces. The VW Y pipe cannot be bought separately, and is not suited for the high temperatures under the hood. Hell, its plastic – what did you expect?!

Dont buy the OEM plastic part when you can buy this BILLET ALUMINUM TIG Welded replacement part for half the price!

If you need a custom water temp sensor port welded on, please let us know. We are happy to perform customization on ANY of our products.

Replaces the following OEM P/N :

1H0-122-101E (1H0122101E) – MK3 Golf/Jetta VR6
3A0-122-101E (3A0122101E) – VR6 Passat
1C0-121-438A (1C0121438A) – New Beetle

[GruvenParts.com]

MKIII 2.0 ABA Billet Lightweight Crank, Tensioner, and Alternator Pulleys – NON-UNDERDRIVE!

www.GruvenParts.com offers precision CNC billet lightweight (and Non-Under-driven) crank, tensioner, and alternator pulleys for the ABA 2.0 engines. The pulley set reduces engine rotating mass by over 4 lbs to help you squeeze out every last bit of power, without the problems associated with under-driving components. Our billet tensioner comes ready to install with a 20K rpm bearing to replace the cheap OEM plastic pulley. The crank pulley is a slick dual design which incorporates the power steering v-belt pulley with a light mounting flange (new shorter grade 12.9 attach bolts included). Finally, the alternator pulley is a paper light version of the OEM steel pulley to minimize parasitic losses.

Check out www.GruvenParts.com for all the billet goodies!

These parts replace the following OEM part numbers :

037-105-243A (037105243A) ABA crank pulley
037-105-253 (037105253) ABA power steering pulley
028-145-278E (028145278E) ABA serpentine tensioner pulley (also fits MK3 TDI)
028-903-119F (028903119F) and 028-903-119AA (028903119AA)ABA alternator pulley

[GruvenParts.com]

GruvenParts.com builds bulletproof TIG welded Y Pipes to replace the OEM plastic in your VW coolant system!


Billet Upper Radiator Hose Y Pipes

PLEASE NOTE : This part is professionally TIG welded! There are no junk tapped threads into thin wall aluminum like the lesser versions offered by unscrupulous rip off artists. And its warranted for life!

An absolute MUST HAVE for all MK3 VR6 owners and MK4 New Beetle owners. The upper radiator hose on these models is quite a pricey item from the dealer – usually about $100. The most documented cause of replacement on this hose is due to the plastic Y fitting which connects the 3 short hose pieces. The VW Y pipe cannot be bought separately, and is not suited for the high temperatures under the hood. Hell, its plastic – what did you expect?!

Dont buy the OEM plastic part when you can buy this BILLET ALUMINUM TIG Welded replacement part for half the price!

If you need a custom water temp sensor port welded on, please let us know. We are happy to perform customization on ANY of our products.

Replaces the following OEM P/N :

1H0-122-101E (1H0122101E) – MK3 Golf/Jetta VR6
3A0-122-101E (3A0122101E) – VR6 Passat
1C0-121-438A (1C0121438A) – New Beetle

[GruvenParts.com]

www.GruvenParts.com

[GruvenParts.com]

Bump for more billet parts !

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

DOES NOT COME WITH CHEAP THIN WALL TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

Ours are completely tig welded by our licensed commercial jet aircraft repair facility! We were the 1st to build this part and its what started us off! If you have a billet crack pipe in your VR6, chances are it was made by http://www.GruvenParts.com. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! The 12V version replaces OEM p/n 021-121-050C (021121050C) and the 24V version replaces OEM p/n 022-121-050 (022121050).

[efritsch]

Any chance you make the V-Belt style pulleys for the P/S, Water Pump and Outer Crank on a G60?

Or the waterneck on the side of an 8v head or the thermostat housing on the bottom of the water pump?

[GruvenParts.com]

We do have the G60 crank pulleys, in stock ready to ship. See the MK2 section of www.GruvenParts.com

[GruvenParts.com]

Billet 12V VR6 Drive Belt Pulleys - All 12V VR6

GruvenParts.com offers a complete set of ultra sleek lightweight 12V VR6 power pulleys. These include lightweight billet crank, power steering, water pump, tensioner, and alternator pulleys for your 12V VR6 engine. These pulleys are precision CNC'd from aircraft grade billet aluminum and reduce the rotating mass by a whopping 8.5 lbs! All pulleys ARE NORMAL DRIVE (NOT UNDER-DRIVE). These pulleys will not change the speed of the supercharger and will not void any supercharger warranties.

Buy them as a set and save!

These pulleys replace the following OEM part numbers :

Crank Pulley : 021-105-243 (021105243)
Tensioner Pulley: 021-145-299 (021145299)
Water Pump Pulley: 021-121-031A (021121031A)
Alternator Pulley: 021-903-119 (021903119)
Power Steering Pulley : 021-145-255 (021145255)

[GruvenParts.com]

AAA VR6 Billet Dipsticks

www.GruvenParts.com is proud to release this Billet Dipstick for all AAA VR6 Corrado, Golf, Jetta, and Passat!

The gorgeous dipstick is CNC’d from a chunk of aerospace grade aluminum and contains 2 chemically resistant O-rings for a perfect fit and seal.

Get rid of the ugly plastic dipstick and replace with our billet version!

This part replaces the dipstick on AAA VR6 engines found on Corrado VR6, MK3 Golf, Jetta, and Passat with OEM dipstick p/n 021115607 and OEM tube p/n 021115629E.

[GruvenParts.com]

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

MACHINED FROM 6061-T651 ALUMINUM TO EXACTLY MATCH OEM PIPE DIMENSIONS - OURS DOES NOT COME WITH CHEAP THIN WALLED TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

GruvenParts.com was the 1st to build this part and it’s what started us off! We manufacture this pipe EXACTLY to match the OEM part shape so there is NEVER a fitment issue. Be careful when considering other billet pipes which do not match the exact shape of the OEM pipe. The fitment of this part is tricky and the shape MUST BE IDENTICAL to the OEM part to ensure correct alignment between the water pump and thermo housing.

If you have a billet crack pipe in your VR6, chances are it was made by us. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! Our pipe has a modular design which allows you to plug the oil cooler feed line with a ¼ NPT plug if installing an external oil cooler. Ours can also be ordered with a chrome plated drain valve for quick and clean coolant flushes. The pipe can also be ordered with a brilliant chrome finish for those seeking the ultimate engine bay bling!

If you dont want to do this job again, buy the LIFETIME WARRANTED GruvenParts.com billet CrackPipe !

Make sure to see our website for the complete installation DIY

The 12V version replaces OEM p/n 021-121-050C (021121050C) found in 12V VR6 : VW Corrado, Golf, Jetta, Passat, and Eurovan.
The 24V version replaces OEM p/n 022-121-050 (022121050) found in 24V VR6 : VW R32, Golf, Jetta, Eurovan, EOS, Audi : 3.2L V6 TT and A3

[GruvenParts.com]

CNC Pressed MSD Coil Pack Brackets for MK3 and MK4 VR6 !

Use this CNC formed, powder coated Aerospace grade aluminum bracket to mount your new MSD 8224 coils on MK3 or MK4 VR6 engines. We all know how poorly the OEM Beru units hold up - so get serious about your VR6 ignition and step up to MSD! Leave the cheaply made, overpriced Beru coils for the competition!

[GruvenParts.com]

Billet VR6 Crack Pipes for ALL VR6 Engines Corrado thru R32!

DOES NOT COME WITH CHEAP THIN WALL TAPPED FITTINGS LIKE OTHER LESSER PIPES !!

12V and 24V VR6 Coolant Pipes aka Crack Pipes

Ours are completely tig welded by our licensed commercial jet aircraft repair facility! We were the 1st to build this part and its what started us off! If you have a billet crack pipe in your VR6, chances are it was made by http://www.GruvenParts.com. Hand crafted in our Aerospace shop using O-rings from the Boeing 777, proven by many hours of track time, it's the highest quality crack pipe you can buy. It's on all of our track cars and has withstood countless hours of track abuse! The 12V version replaces OEM p/n 021-121-050C (021121050C) and the 24V version replaces OEM p/n 022-121-050 (022121050).

[GruvenParts.com]

Billet 12V VR6 Drive Belt Pulleys - All 12V VR6

GruvenParts.com offers a complete set of ultra sleek lightweight 12V VR6 power pulleys. These include lightweight billet crank, power steering, water pump, tensioner, and alternator pulleys for your 12V VR6 engine. These pulleys are precision CNC'd from aircraft grade billet aluminum and reduce the rotating mass by a whopping 8.5 lbs! All pulleys ARE NORMAL DRIVE (NOT UNDER-DRIVE). These pulleys will not change the speed of the supercharger and will not void any supercharger warranties.

Buy them as a set and save!

These pulleys replace the following OEM part numbers :

Crank Pulley : 021-105-243 (021105243)
Tensioner Pulley: 021-145-299 (021145299)
Water Pump Pulley: 021-121-031A (021121031A)
Alternator Pulley: 021-903-119 (021903119)
Power Steering Pulley : 021-145-255 (021145255)

[GruvenParts.com]

MK2 / MK3 Billet Fuel Line Support Brackets

Billet fuel line support brackets (set of 2) to replace the weak plastic clips that are probably long gone on your MK2 and MK3 VR6. Ours are CNC'd from billet aluminum to perfectly match the size and shape of your VR6 fuel lines. Mount directly to the head in place of existing plastic supports and install with supplied aerospace grade stainless fasteners. Dont leave your VR6 fuel lines loose and rubbing against hot engine components! These will take more abuse than you can dish out, guaranteed!!

Can be chrome plated for those seeking even more engine bay bling.

Fits all MK2 and MK3 VR6 - Jetta, GTI, Passat, and Corrado. Includes stainless bracket hardware, re-use existing 10mm nuts to bolt to head. Brackets replace OEM P/N 021-133-827 (021133827) Bracket and P/N 021-133-687A (021133687A) clip.

[GruvenParts.com]

GruvenParts.com builds bulletproof TIG welded Y Pipes to replace the OEM plastic in your VW coolant system!


Billet Upper Radiator Hose Y Pipes

PLEASE NOTE : This part is professionally TIG welded! There are no junk tapped threads into thin wall aluminum like the lesser versions offered by unscrupulous rip off artists. And its warranted for life!

An absolute MUST HAVE for all MK3 VR6 owners and MK4 New Beetle owners. The upper radiator hose on these models is quite a pricey item from the dealer – usually about $100. The most documented cause of replacement on this hose is due to the plastic Y fitting which connects the 3 short hose pieces. The VW Y pipe cannot be bought separately, and is not suited for the high temperatures under the hood. Hell, its plastic – what did you expect?!

Dont buy the OEM plastic part when you can buy this BILLET ALUMINUM TIG Welded replacement part for half the price!

If you need a custom water temp sensor port welded on, please let us know. We are happy to perform customization on ANY of our products.

Replaces the following OEM P/N :

1H0-122-101E (1H0122101E) – MK3 Golf/Jetta VR6
3A0-122-101E (3A0122101E) – VR6 Passat
1C0-121-438A (1C0121438A) – New Beetle

[GruvenParts.com]

Bump for billet parts !

Billet 12V VR6 Drive Belt Pulleys - All 12V VR6

GruvenParts.com offers a complete set of ultra sleek lightweight 12V VR6 power pulleys. These include lightweight billet crank, power steering, water pump, tensioner, and alternator pulleys for your 12V VR6 engine. These pulleys are precision CNC'd from aircraft grade billet aluminum and reduce the rotating mass by a whopping 8.5 lbs! All pulleys ARE NORMAL DRIVE (NOT UNDER-DRIVE). These pulleys will not change the speed of the supercharger and will not void any supercharger warranties.

Buy them as a set and save!

These pulleys replace the following OEM part numbers :

Crank Pulley : 021-105-243 (021105243)
Tensioner Pulley: 021-145-299 (021145299)
Water Pump Pulley: 021-121-031A (021121031A)
Alternator Pulley: 021-903-119 (021903119)
Power Steering Pulley : 021-145-255 (021145255)