USP Fall Sale: 2.5L Testpipe or High Flow Cat pipe From $230

[Gregg@USP.MotorSports]

Well I ordered one today. Thank you for the discount greg, can't wait to install it.

hope you enjoy it

[tchilds]

all good, just managed to throw a cel lol. go figure. will get it coded out eventually, no big deal.

over all the pipe fit pretty well. it did end up a tiny bit short on my 09+ rabbit and moved my exhaust tips a lil w/out the subframe hanger.

the car pulls nice now, rev's much easier now in neutral. over all pretty happy! just wish the o2 sensor spacer would have worked!

[TylerO28]

Ok I'm thinking about picking one up, will I notice quicker spool with it being opened up? I'm hoping so

[tchilds]

dunno but the stock cat was definitely restrictive as heck on the 2.5. my car runs a lot better w/out it now.

[kevin FaKiN spLits]

dunno but the stock cat was definitely restrictive as heck on the 2.5. my car runs a lot better w/out it now.

Its like trying to breathe through a punching bag long ways

[JR Martinez]

Will it fit a 2.5 L 2012 Beetle?

[Gregg@USP.MotorSports]

Will it fit a 2.5 L 2012 Beetle?

we have not test fitted it yet

[tchilds]

Sounds like you have a tester

[Gregg@USP.MotorSports]

still got a few left i can offer at this price

[burkedub711]

whats the advantcage to the high flow cat?

[spartanrabbit09]

whats the advantcage to the high flow cat?

It is easier for you to pass emissions....at least in CT

[jaja123]

whats the advantcage to the high flow cat?

I have the high flow version. The advantages I think are no smell which also means less police suspicion. Less rasp maybe but I don't know as mine sounds very similar to no cat. Also the chance of a cel may be less. AS for gains they should be very close. This high flow cat flows very well. I took a fan to it and it blew out the other side with near the same velocity. I did the stock mid pipe and it obstructed the air a good amount.

[2pt5_20v_pwr]

still got a few left i can offer at this price

whats the promo code trying to order a testpipe and need it by thursday

[Gregg@USP.MotorSports]

got a few more test-pipes in stock, PM me for the days deal

[Zaytri]

Testpipe: 2 ME: .75

For those that are semi-mechanically inclined, but have never done anything with exhaust/headers/etc.. The concept of the install is EASY.

Until you try to remove your o2 sensor... Fail #1
No form of wrench or dousing of PB blaster worked on this SOB
Ordered a specific o2 wrench of amazon. Continued Fail.
Solution? remove the plastic cover where the o2 sensor wire connects, disconnect wire, remove pipe. Step on pipe, remove o2 sensor, scream out loudly like a victorious barbarian.

Put in your fancy new pipe, bolt it all up nicely, only to realize one of the 4 rusted, corroded, grimy looking bolts that connect your testpipe to the exhaust header is stripped FAIL #2.
Solution? Hook it up with 3 bolts, swear loudly that it's after 6pm on a sunday and there no where to go to get a bolt.

Then proceed to drive it around, as it sounds SEXY, and gave a nice little kick in the seat along with the lightweight flywheel you installed earlier.

Which leads me to my next question.. Does anyone know the part number for this? Can i match up the thread at a hardware store and screw in a normal headed bolt as opposed to that strange 2 sided threaded contraption they have on there stock?

[Gregg@USP.MotorSports]

Testpipe: 2 ME: .75

For those that are semi-mechanically inclined, but have never done anything with exhaust/headers/etc.. The concept of the install is EASY.

Until you try to remove your o2 sensor... Fail #1
No form of wrench or dousing of PB blaster worked on this SOB
Ordered a specific o2 wrench of amazon. Continued Fail.
Solution? remove the plastic cover where the o2 sensor wire connects, disconnect wire, remove pipe. Step on pipe, remove o2 sensor, scream out loudly like a victorious barbarian.

Put in your fancy new pipe, bolt it all up nicely, only to realize one of the 4 rusted, corroded, grimy looking bolts that connect your testpipe to the exhaust header is stripped FAIL #2.
Solution? Hook it up with 3 bolts, swear loudly that it's after 6pm on a sunday and there no where to go to get a bolt.

Then proceed to drive it around, as it sounds SEXY, and gave a nice little kick in the seat along with the lightweight flywheel you installed earlier.

Which leads me to my next question.. Does anyone know the part number for this? Can i match up the thread at a hardware store and screw in a normal headed bolt as opposed to that strange 2 sided threaded contraption they have on there stock?

I see you live in NY. In the future you might want to try some heat from a torch to loosen things up. You should be able to match the stud up at a hardware store

[KAKASHIxRABBIT]

I've had mine on for two weeks. Love it!!

[TylerO28]

just get some stainless bolts and some loctite. thread through the flange and BOLT that bad boy together.

i had to clock mine just right to get the turbo downpipe to bolt up. but using bolts and nuts is a MUCH easier approach over using the oem studs. they get brittle as they go through heat cycles and inevitably you'll end up either stripping one or breaking one (i broke one)

overall i REALLY like what usp has made...

great build quality, a nice flex section. and NO CEL!

now my only gripe is with the flex section. it is only a case with anyone that has a turbo. but that flex pipe doesn't flex much. and in turn take A LOT of thinking/loosening the downpipe and exhaust just to get it to line up (barely) but once it does all is well...

I might suggest they make that flex section Just a little bit longer. only to accomodate those of us that have turbo's it's not a big deal, but it could help since i think more and more turbo's are going to be on the road soon

[xxKurt85xx]

I put mine in last week with the high flow cat, and a bosch 02 spacer. my cel came on and vag com reads 02 deficiency. should I try the 42DD 02 spacer and see If that works or.. Is it not gonna make that much of a difference?

[joshGOLF2.5]

i threw CEL as well on my 2010 golf yesterday

[thygreyt]

i threw CEL as well on my 2010 golf yesterday

if you dont have a spacer, then the CEL is more than expected.

[joshGOLF2.5]

if you dont have a spacer, then the CEL is more than expected.

i know theres a few spacers out there but not sure which one to order?

[thygreyt]

i have a 42 draft designs and it works as a charm