VWVortex


+ Reply to Thread
Results 1 to 25 of 25

Thread: WTB: All kinds of small oem parts, fender liners, facelight light harness, navy interior parts.

  1. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-19-2012 04:43 AM #1
    EDIT: I need parts from a pre-face, a face lift car is completely different.


    I'm looking for a bunch of oem parts in good condition (not scuffed, not torn, net chipped or scratched), the first list is all the stuff that could fit in a shoe box...easy stuff to get. If you're making a living parting Audis this probably isn't the ad to look at as I'm looking for great/fair prices not to mention all the things I'm asking for generally go to the dump.

    1) Trunk harness (easy!): pop the trunk, pull back the carpet by the rear drivers side shock tower as seen in the pic below and cut (5 wire bundle). Pull the whole harness with the carpet off the trunk lid. I don't need all the electronics, poppers, bulb holders inside the trunk lid. With the harness I need the 2 semi-large black rubber garmets that the harness goes through trunk jam and trunk hole. They'll pop out with the harness.



    2) Both black plastic trunk hinge cosmetic caps (with no broken tabs)

    3) Inner tail light cosmetic black stud caps (1-2 will work)

    4) This rear seat belt cover thingy and the rear seat belt guide cover strip:


    5) The outer b-pillars have lower cosmetic black caps, I need both sides no broken tabs:


    6) Notice the picture below: I need the part that is on my thumb in black. It's a small corner piece that hides the mirror bolt. Also, where my middle finger is....there's 2 rubber end triangle caps per door card (one on each end). So I need all pieces (8 pieces in all, 2 per door). Be careful not to snap the plastic nipples that hold them on.



    7) The front oil pan steel bracket ...easy removal....there's two, I need the one on the passenger side of the oil pan. It goes from the back side of the oil pan to the front motor mount.

    8) Face-lift cars: ~8 pin new style headlights: I need the headlight wiring harness with all the plugs and enough wire to solder into (8 pin harness plug with wires, rectangle blinker plug and wires, and apparently the fog light harness).


    All those pieces are small, everything in all could fit in one of those ~$7 USPS flat rate boxes (the oil pan bracket should). I maybe adding more stuff
    __________________________________________

    Bigger pieces:

    - 2 mint front fender liners (does not mean an oil bomb went off or 15 years of rust and salt collected on them) When you remove, throw all the screws in a sandwich baggie

    - upper and lower un-cracked timing belt cover.

    - Pre-face lift cars: upper interior b-pillars un-cracked! Any color, face light cars are a no.
    __________________________________________
    Pre-face Navy Interiors

    - The drivers side lower molding strip that goes from the pedal area back the rear seats


    - Interior b-pillars lower and upper un-cracked both sides any color on the uppers or navy works.
    Last edited by The A1 and A2 German; 08-01-2012 at 06:30 PM.
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  2. 03-19-2012 09:01 AM #2
    I can get you most of this stuff,...I just picked up a part out car, but I am in MN. you could also try brian at audis4parts.com
    email mbandit22@yahoo.com
    -Dustin

  3. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-19-2012 11:21 PM #3
    Believe I bought my S4 body parts off him.


    At the moment, have not found anything.
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  4. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-21-2012 04:04 PM #4
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  5. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-22-2012 02:01 AM #5
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  6. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-25-2012 02:08 PM #6
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  7. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-27-2012 04:14 AM #7
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  8. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    03-27-2012 08:06 PM #8
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  9. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    04-11-2012 08:40 PM #9
    Needs pre-face lift interior parts!
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  10. Member SlimQuattro's Avatar
    Join Date
    May 15th, 2008
    Location
    Morgantown WV
    Posts
    662
    Vehicles
    B5 AUDI
    04-11-2012 11:13 PM #10
    I have the plastic mirror bolt covers if u still need them.

  11. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    04-12-2012 02:01 PM #11
    NEED:

    Bigger pieces:

    - 2 mint front fender liners (does not mean an oil bomb went off or 15 years of rust and salt collected on them) When you remove, throw all the screws in a sandwich baggie

    - upper and lower un-cracked timing belt cover.

    - Pre-face lift cars: upper interior b-pillars un-cracked! Any color, face light cars are a no.


    __________________________________________
    Pre-face Navy Interiors

    - The drivers side lower molding strip that goes from the pedal area back the rear seats


    - Interior b-pillars lower and upper un-cracked both sides any color on the uppers or navy works.


    _____________________________________________

    -Water pump pulley/steering pulley with bolts.

    - Oil pan bracket
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  12. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    05-03-2012 04:50 PM #12
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  13. Member teespeed's Avatar
    Join Date
    Apr 17th, 2008
    Location
    Puget sound, Wa
    Posts
    1,022
    05-08-2012 01:46 AM #13
    whats your engine code, i might have the timing belt covers.

  14. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    07-19-2012 06:59 PM #14
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  15. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    07-25-2012 06:32 AM #15
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  16. Member solowb5's Avatar
    Join Date
    Jan 16th, 2007
    Location
    cincinnati, oh
    Posts
    5,833
    07-25-2012 09:18 AM #16
    I have the timing belt covers and lower b pillars for 40 shipped
    [99 Built Porsche 996 c2][Porsche 930 race car (in progress)]
    [01 VW Stage 4 matchstick red gti (for sale)][01 Audi a4 avant]
    [05 VW Touareg modded]
    When using the link. Look to the left for the sub catagories of parts.Picture link for items for sale http://s139.photobucket.com/albums/q...rts%20Catalog/

  17. Member kandst's Avatar
    Join Date
    Mar 9th, 2008
    Location
    sonora
    Posts
    266
    Vehicles
    2000 jetta vr6
    07-25-2012 03:53 PM #17
    hey what parts do you still need i have a 2000 a4 avant that i am parting out

  18. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    07-25-2012 03:59 PM #18
    Just about the whole list minus:


    Pulley

    Ugg...still need belt covers
    Last edited by The A1 and A2 German; 07-25-2012 at 10:21 PM.
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  19. Member kandst's Avatar
    Join Date
    Mar 9th, 2008
    Location
    sonora
    Posts
    266
    Vehicles
    2000 jetta vr6
    07-25-2012 05:09 PM #19
    ok i have all of the interior parts that you nee in the front half of the car mainly because my car is the avant wagon the back stuff is different

  20. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    08-01-2012 01:28 AM #20
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  21. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    08-01-2012 06:34 PM #21
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  22. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    09-01-2012 09:53 PM #22
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  23. 09-02-2012 12:44 AM #23
    I have all the fender liners no hardware tho

  24. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    09-04-2012 01:22 AM #24
    All right, I'll keep in the mind, hopefully looking for everything at once.
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

  25. Member The A1 and A2 German's Avatar
    Join Date
    Nov 17th, 2002
    Location
    Tempe, AZ 85281
    Posts
    11,981
    Vehicles
    Sonoma S-15, Mark 3 Caddy, Audi A4, 71 CL175, 71 CB350, 69 Stinger, V-Twin Chopper, A4 SC'd Avant,
    09-11-2012 11:47 PM #25
    FS:Extensively Moddified 350+ hp Mark I to Mark III conversion Caddy truck:
    http://forums.vwvortex.com/showthrea...dy-W-Video-10K
    FS: Custom '69 Stinger FS: iForged 3 Piece 19x9 5x112 Falken 452's
    FS: Custom '73 CB350 Museum Piece, 8 miles FS: 10' V-Twin Chopper: SOLD

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts