need some help choosing my tire size.
18x8.5 et 44 15mm adapter
18x9.5 et 46 15mm adapter
im thinking 215/40 and 225/40 but im not sure if they will rub or not.
Will this fit on my mk4 jetta?:
16x7.5 et 25
16x9 et 25
205/55 all around.
Sizes and offset can be played with. I have 8mm spacers up front right now, but they don't need to be used. I'm not wanting poke really, just flush with the fender.
also, if you look at the Mk4 Wheel Offset and Stance Picture Index you can see a 9 et25 listed. that will show you a picture of what yours will look like in the rear, except for the fact that your wheels are 16's.
Last edited by Clean PG; 04-20-2012 at 08:32 AM.
9.5 widened longbeach
What's the best thickness of spacer i need to fit little poke rear, more flush than poke front (little poke)?
Well, What's the perfect offset for 9.5 inch wheels on a mk4 Jetta?
Thinking of 35mm rear for an final ET28.4 et maybe 25mm in front for final ET38.4?
215/45 should fit perfectly for the stretch?
Thank you all!
Hello ! form Kazakhstan
Soon I will get my XXR 522 18" 9.5J et 38 all around.
tires will be 225/35/18.
which spacers i must install all around ? 20 mm or more ?
Do I need to roll out my wheel arches?
sorry for my bad english
My car http://www.drive2.ru/cars/skoda/octavia_tour/octavia_tour/bob911/
Eibcah prokit -30 all around -50 mm cut spring, Koni STR.T.
FK front Strut bar, rear from Skoda Octavia RS + custom
Engine - 2.0 8v stock
Hey . Picking up new wheels tomorrow.
I was thinking
205/40 for The front
215/40 for the rear.
Most likely yoko s drives or nitto neo gens
I'm already low and fenders rolled.
What do u guys think?
So, i decide to make two of them 8.5 inch, which will probably give me more facility for the final setting for the front axle.
So, 40mm spacers for rear wheels (9.5) for final ET23.4, and 33mm spacers for front wheels (8.5) for final ET17.7
That's ok i think?
But, because now i'm not going to ride a squared setup, what's the correct size of tires i need to have an almost perfect overall diameter between front and rear?
Would like to run 205/45, but want to be sure it's going to fit well...
Need approbation plz!
Last edited by Clean PG; 04-23-2012 at 12:34 PM.
Picking up a set of wheels pretty soon and curious to see if they will fit...
18x8 et35 audi pattern. Going to run 5x100-5x112 15mm adapters.. Which should give me a final of et20 all the way around.. Is that going to look like total ass or? I really want to run these wheels but them starting with et35 offset its not giving me much of an option.. Thanks Guys
__________________________________________________ __Follow Me @ Kuncle_________________________________________
__________________________________________________ ______The Chive__________________________________________________ __
2011 Sawblades Thread
and your rears with a 20mm would poke 5mm less than this photo:
so you'll be fine running 15-20mm adapters with those audi wheels. for tires i'd do 205/40/18 if you havent made up your mind on that already (that's the size in those pictures)
Last edited by Clean PG; 04-24-2012 at 09:16 AM.
I bought BBS CH's
18x8 ET40 w/ 18mm Bolt Pattern adapters
18x9 ET35 w/ 18mm " "
my 00' 1.8t's dropped about 3.5 inches..
i currently have 2 225/40's for the 18x9's
and buying 215/40's for the 18x8's
how's it gunna look?
will i have like..tons of poke or whaaa?
im new abit to the whole poke/flush look since before i never had any of that since i ran 17x7.5 audi a8 ET35 without spacers or nothing.
and if anyone has any pictures of what it might look like dont be shy! lol
2000 1.8T Jetta | ChrissTapp Eurodyne Chipped(20 PSI) | Single Gutted Cat To Magnaflow Muffler | RK Coils Dropped 3.5 | Stage 2 Bully Clutch | Blacked Head & Tails | AEM Cold Air | Badgeless Grill |17x7.5 ET35 Audi A8 Replica's |
[Staggerd' BBS CH Black W/ Polished Lip (New) 18x8 ET35/18x9 ET40]