#1
Hello, all,
I've been suffering for this issue for quite a while. My passat 06 is experience a hard time to start up after sitting over night. The first attempt in the morning is always shaky. Then, it starts up okay during the day. Even like after driving 5 mins and I can restart it without any problem. But it's the first time of the day that troubles me.
And some history, my battery died completely like 2 months ago, and I replaced it with a Duracell. At first, it has no problem start up at all. But there was one day I forgot to turn of the lights and leaved my car over night. The next morning, I was able to start it but with some difficulty. Since then, I have been experiencing hard times in starting up. Any body can offer some solution? Or point out the issue? I'm really afraid to have a dead battery in a parking lot 1 hour away from my apartment againThank in advance.
![]()
#2
Unitronic > APR Switched from APR to UNI and never looking back
CW '10 Passat 2.0TSI: UNI Stage 2 VMR V705 19x8.5 et45 Podi Boost gauge/pod AWE DV, Turbo Outlet Pipe BSH Boost Tap BillyBoat 3" TBE BFI Stg2 Dogbone/motor mount/trans. mount KW V2 coils Forge Twintake(1st on Passat/CC) JBL W12GTi MKII HEX+CAN vagcom, Podi.ca podi free ship code: NINOSHIP, VMR | Wheels velocitymotoring.com, VolksBHAN in September
#3
I have a similar issue, it would almost pull the car a small bit, almost like it was in gear or something, dont think its a battery though. never really focused on it too much.
Audi A4 B5 Avant 99
I have not failed. I've just found 10,000 ways that won't work.
#4
if yoy have a 2.0t and it only happens after the car has sat overnight and its cooler out its is prob due to carbon build up on the intake valves. It is know to cause cold start issues
Unitronic Stage III w/ PT5558BB Turbo (What a difference UNI is from APR!!)Unitronic.ca,HPFP Upgrade Stage 1 pump, 3in.TBE, BSH throttle pipe/27mm RSB/Endlinks , Forge 007 DV , RalcoRC SS, 42Draft Design CNC Shifter bushings, N2MB WOT box, BFI stage 2 motor/tranny mounts, 034 Dogbone, Koni FSD shocks, Neuspeed springs/25mm FSB, Whiteline Anti-lift kit/Front control arm bushings, 18x8.5 VMR VB3s, JBL stereo, CTS Turbo 2.0t FSI Big turbo kit!
#5
#6
#7
#8
Unitronic > APR Switched from APR to UNI and never looking back
CW '10 Passat 2.0TSI: UNI Stage 2 VMR V705 19x8.5 et45 Podi Boost gauge/pod AWE DV, Turbo Outlet Pipe BSH Boost Tap BillyBoat 3" TBE BFI Stg2 Dogbone/motor mount/trans. mount KW V2 coils Forge Twintake(1st on Passat/CC) JBL W12GTi MKII HEX+CAN vagcom, Podi.ca podi free ship code: NINOSHIP, VMR | Wheels velocitymotoring.com, VolksBHAN in September
#9
I know you guys probably don't have a 1.9tdi in US, but anyone know if the carbon built up could be the issue on my car? its a 06 with 260K KM so im guessing the build up could be quite severe![]()
Audi A4 B5 Avant 99
I have not failed. I've just found 10,000 ways that won't work.
#10
#11
Unitronic>Revo and hauling ass! K04 w/ RS4 injectors, Forge WINtake, Eurojet intercooler, ECS lightweight pulley, APR TBE, APR hpfp, BSH TB pipe, Forge DV, Neuspeed K04 discharge pipe, ECS dogbone mount, BFI stage 2 engine & tranny mount, 42 DD Ultimate catch can, HPFP Upgrade 145 BAR FRV, Snow Performance Stage 2 water/meth kit, Level 10 valve body rebuild
#12
Like Red said sea foam will do next to nothing that carbon is like concrete.
Diy-ing isnt really hard just tedious and time consuming
Sent from my Galaxy SIII
Unitronic Stage III w/ PT5558BB Turbo (What a difference UNI is from APR!!)Unitronic.ca,HPFP Upgrade Stage 1 pump, 3in.TBE, BSH throttle pipe/27mm RSB/Endlinks , Forge 007 DV , RalcoRC SS, 42Draft Design CNC Shifter bushings, N2MB WOT box, BFI stage 2 motor/tranny mounts, 034 Dogbone, Koni FSD shocks, Neuspeed springs/25mm FSB, Whiteline Anti-lift kit/Front control arm bushings, 18x8.5 VMR VB3s, JBL stereo, CTS Turbo 2.0t FSI Big turbo kit!