VWVortex


+ Reply to Thread
Results 1 to 2 of 2

Thread: Feeler: 98 GTI VR6

  1. 10-04-2012 06:51 PM #1
    Seeing if there's any interest in my car.


    Engine:
    Rebuilt 12V VR6 w/10K(New rings, bearings, seals, timing chains, guides, tensioners, sensors and oil pump)
    Fully rebuilt Cylinder head (Milled surface, 3-angle valve job, hot tanked, new lifters, New valve guides & seats)
    Engine Harness has been gone through to eliminate unnecessary connectors and completely rewrapped in new friction tape
    New water distribution pipe thermostat housing and all brand new cooling system parts (all new sensors and gaskets)
    Custom aluminum fan shroud powder coated wrinkle black w/ 2 12" slim electric fans
    Eurosport oil cooler with thermostatic sandwich plate
    BFI Stage 1 Poly engine mounts

    Transmission:
    02A 5 speed (rebuilt with new syncro's and bearings)
    Mk4 shift box & tower w/Dieselgeek Sigma SS
    50/50 Redline lightweight shockproof & MT-90

    Chassis:
    Mk3 GTI VR6 w/150K
    H&R Ultra Low stage 3 coilovers
    Autotech hollow sway-bars front and rear (28mm rear and 25mm front)
    All new bushings (Strut mounts, control arms, sway bars)
    Autotech rear upper tie-bar and OMP front upper tie-bar (both powder coated wrinkle black)
    All new wheel bearings
    New rear brembo rotors w/ Ceramic pads
    Mk4 Rear calipers
    ECS stainless brake lines (Front, middle, and rear)
    BBS RX wheels 17x7.5 35MM offset (black chrome powder coat over chrome)
    Nitto NeoGen all season tires 205/40/17

    Exterior:
    Porcelain Blue metallic (Engine bay freshly resprayed)
    Shaved keylock on drivers door handle
    Bonrath 2 bar badgeless grille
    Shaved front bumper (no lights or side markers)
    OEM european VR6 lip spoiler
    Rear bumper shaved exhaust cut-out
    Mk3.5 Cabrio Clip-in door moldings
    Cabrio rear plate recess welded into stock hatch
    Canadian CL spec rear glass (No spolier holes or 3rd brake light)
    Smoked E-code headlights
    Hella RSR tail lights
    Shaved fuba roof antenna
    Roof painted SEM trim black
    European Core support & rebar

    Interior:
    Black cloth
    Rewrapped headliner and pillar trim in OEM 20th anniversary GTI black cloth
    All grey pieces either trim dyed or bought brand new in black (grab handles, sunroof switch, visors)
    Recaro "trophy" seats rewrapped in black OEM Nissan fabric w/ blue stitching (Fade resistant and stain resistant)
    Rear seat wrapped in same material to match
    MOMO Jet steering wheel w/ hub
    Anniversary Edition e-brake cover and floor mats all blue stitched
    Entire floor, hatch area, rear quarter panels, roof and doors lined with Dynomat (exhaust tunnel double layered)
    Brushed aluminum cabrio door pulls
    Brushed aluminum ABT door pins
    Blue and red lit cluster
    Red lit A/C controls, dash switches, window switches, mirror switch, and euro headlight switch
    Alpine Head unit with full speed iPod attachment
    2 sets of Infinity Kappa Components
    Inifinity Basslink self powered sub

    8K OBO Located in PHX AZ













    Last edited by 20V_DUBBIN; 10-09-2012 at 06:32 AM.

  2. Member Sonic303's Avatar
    Join Date
    Nov 13th, 2009
    Location
    5280
    Posts
    1,977
    Vehicles
    '98 PBM Vento GLX
    10-06-2012 06:03 PM #2
    Awesome car

+ Reply to Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts