Search Results - VWVortex
Username or Email Address
Do you already have an account?
Forgot your password?
  • Log in or Sign up

    VWVortex


    Search:

    Type: Posts; User: tyrone27

    Page 1 of 150 1 2 3 4

    Search: Search took 0.97 seconds.

    1. I use 20w 50 all the time. Switch to 10w 30 in...

      I use 20w 50 all the time. Switch to 10w 30 in winter

      Sent from my LM-V600 using Tapatalk
    2. Thread: Ms ground

      by tyrone27
      Replies
      1
      Views
      381

      Ms ground

      Finally getting around to installing the fuse block. Thinking if I should run primary ground to negative battery terminal or the rear of the engine....
    3. Replies
      79
      Views
      8,378

      UPDATE: tried to tune yesterday and the 02 sonsor...

      UPDATE: tried to tune yesterday and the 02 sonsor failed. Ordered a new sensor and will install tomorrow. Also pulled timing maps off vortex and im going to be redoing my maps tomorrow.

      Got a...
    4. Replies
      79
      Views
      8,378

      UPDATE: got a alignment done finally now it...

      UPDATE: got a alignment done finally now it drives straight. Went and removed fuel from the ve table now builds boost faster. Also replaced the intake boot today to a 3.25in to 2.5 90 degree bend and...
    5. Replies
      1,929
      Views
      996,177

      Chassis: b3 passat Block: stock 9A Pistons:...

      Chassis: b3 passat
      Block: stock 9A
      Pistons: stock
      Rods: stock
      Head: 9A
      Head gasket: TWO steel ABA w/ arp headstuds
      Cams: stock
      Valves: stock
      Intake manifold: stock
      Throttle body: stock with...
    6. Replies
      13
      Views
      1,440

      You could put lock pliers on the very top of the...

      You could put lock pliers on the very top of the studs to get them off but you would have to take them to a machine shop to get them redone. But also ask the shop to widen the holes a little.
      ...
    7. Replies
      13
      Views
      1,440

      you can. but like he said if they all went on...

      you can. but like he said if they all went on with the head they should come off too.
    8. Replies
      13
      Views
      1,440

      Remove the studs that's what's holding the head...

      Remove the studs that's what's holding the head down keeping it from moving. I have ARP head studs and I need a Allen head socket to remove them before I can get the head off.

      Sent from my...
    9. https://www.ebay.com/itm/174169072069 That's the...

      https://www.ebay.com/itm/174169072069
      That's the distributor it's 35 bucks

      And get a valve cover gasket kit and replace the gaskets the one in the center is leaking

      Sent from my LM-V600 using...
    10. Replies
      79
      Views
      8,378

      UPDATE: It's up and running at 5psi. After 2...

      UPDATE:

      It's up and running at 5psi. After 2 days of diagnostic on the spark cut and stalling when I went into boost. Problem was I damaged the coil wire when reinstalling the intercooler piping....
    11. Replies
      3
      Views
      502

      I fixed it problem with the coil wire to...

      I fixed it problem with the coil wire to distributor was cut. Also Injector 1 wiring was cracked.*

      Sent from my LM-V600 using Tapatalk
    12. Replies
      3
      Views
      502

      https://youtu.be/3u3xxYGlPlM No sync loss or...

      https://youtu.be/3u3xxYGlPlM

      No sync loss or errors in logs.

      Sent from my LM-V600 using Tapatalk
    13. Replies
      3
      Views
      502

      16vt megasquirt stalling

      have a ms2 and its stalling and cutting out when i give it hard acceleration. tried taking away fuel and adding fuel. even stalled twice while regular driving. have datalogs but i can't see where...
    14. Replies
      79
      Views
      8,378

      UPDATE: it's back together. So current setup is :...

      UPDATE: it's back together. So current setup is :

      80lb Injectors
      (2) aba headgaskets
      Gt35
      2.5in exhaust
      2.5in intercooler piping
      Air to water intercooler
      Ms2
    15. Replies
      79
      Views
      8,378

      Here is how you modify the aba headgaskets to fit...

      Here is how you modify the aba headgaskets to fit on the...
    16. Replies
      79
      Views
      8,378

      UPDATE: spent 1 hour trying to start the car...

      UPDATE: spent 1 hour trying to start the car today and wouldn't start. had fuel and spark and checked timing. replaced plugs to and still no start. well then I realized that I never took the...
    17. Replies
      79
      Views
      8,378

      thanks. i've been working on it in my spare...

      thanks. i've been working on it in my spare time. i have 4 other projects going on too.
    18. Replies
      79
      Views
      8,378

      UPDATE: intercooler mounted. Next have to run...

      UPDATE: intercooler mounted. Next have to run hoses and pump. https://uploads.tapatalk-cdn.com/20200817/60126f866323f77455a374e68e5a03b3.jpg

      Sent from my LM-V600 using Tapatalk
    19. Replies
      79
      Views
      8,378

      Got the piping done...

      Got the piping done...
    20. Could be the wire or distributor Sent from my...

      Could be the wire or distributor

      Sent from my LM-V600 using Tapatalk
    Results 1 to 20 of 3000
    Page 1 of 150 1 2 3 4
    vwvortex.com is an independent Volkswagen enthusiast website owned and operated by VerticalScope Inc. Content on vwvortex.com is generated by its users. vwvortex.com is not in any way affiliated with Volkswagen AG.